Thanks Guys.... seems it was the fuser... we don't get that deep into the fuser. I just swapped it with a refurb. Printed about 75 pages with no problems ... ...
Yep - its 95 over here. Cheers, Marcus ... From: printerrepair@yahoogroups.com [mailto:printerrepair@yahoogroups.com]On Behalf Of Russ Blakeman Sent: Thursday,...
Hello gurus - hope you can help me. I reached a dead end! During initialization I get the message LOAD FILE AND EXECUTE and stops. I already removed the...
In case anyone else runs into this - there is an error in the LJ1200 service manual under the secondary error codes. The light patterns for Laser/Scanner...
Does this have an EIO hard drive? ... From: printerrepair@yahoogroups.com [mailto:printerrepair@yahoogroups.com]On Behalf Of Leo Sent: Friday, September 02,...
Also you say firmware update - is the for the printer or the Jetdirect? The JD might be in need of a firmware flash too. You'll need the HP download manager to...
Weekend? What's that LOL ... From: printerrepair@yahoogroups.com [mailto:printerrepair@yahoogroups.com]On Behalf Of Leo Sent: Friday, September 02, 2005 8:44...
Hi Russ, thanks for the messages. The update was of the printer fimware. We removed the JetDirect, powered the machine and got the same error message - we...
I was just given a Panasonic KX-P4410 laser printer and when I turned it on it made a poping noise, and in the lcd dispaly it says Call For Service E31. Does...
I found out by searching the group that E31 is a fuser error. I have found several sources for new fusers, is this something the average individual user can...
Jim; The board that the fuser plugs into usally has cold solder joints or broken solder joints. Check the board first before ordering a fuser. Bob ... From:...
Jim, I think E31 is a fuser problem, but it may be the power supply. I used to repair the 4420 power supplies by resoldering the cracked leads that bring the...
Jim O'Connell
joconnell@...
Sep 6, 2005 2:21 pm
18633
You have one odd error then, my guess would be next that you should look into possibly changing the formatter. Find a vendor that will allow return with small...
That would account for the popping noise if the noise he referred to was an electrical arcing type of popping. The LJ5L and 6L printers get bad solder joints...
Should be the formatter, have seen a couple of exchange-cores come through that have had that same error. ... From: Russ Blakeman [mailto:rhb57@...] ...
techsupp
techsupp@...
Sep 6, 2005 2:37 pm
18636
Leo, I had this same error recently, while I was troubleshooting an EIO that the LJ4200 wouldn't recognize. I had swapped slots and suddenly started getting...
E31 is a fuser error. Usually caused by a bad heating lamp in the fuser. For most it is easier to replace the fuser as an assembly than to try to take it...
He might not have tried the GO button but one of my clients at a local hospital seems to have a user that likes to do that - fun trying to figure out usage...
In this business, you get the ordinary and mundane, sometimes you get a challenge ... and then you have the bizarre. I got a service call yesterday to look at...
I've had similar complaints and looked at things like moisture in the area and such - a few cheaply reworked fusers will smell when cold going to hot - usually...
Thanks, Russ, appreciate the quick reply. 3 out of 4 have the original oem fuser, and all of them have a genuine HP toner ctdg in them. This is a large company...
Was wondering if anyone has experienced this printer randomly stopping with a paper jem error. One page is 1/2 way between the fuser and the exit rollers...and...
Hi Marcus, Thanks for the quick response and the heads up on the 10ex's dismantlement requirements. :) At first glance, the arrays look similar - but one's at...
I see fusers well beyond the 350k all the time around here - people just ignore (or never see) the Perform Maint message and until it acts up they have no...
I have an HP officejet d145. Yesterday the front LCD began flashing error message "Photo card is in backwards...". There is no card in the reader, I never...
Hi all, HP6110 all-in-one "Original Jam" problem.What does it mean? When power on scanner unit not move smoothly and don't stop? [Non-text portions of this...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
