thanks to all who responded i tried to follow the latest advice below - ... Usually happens if the drawer is opened during a printjob..You'll have to ... ...
I need to replace the Drum Unit on my KX-P4410, and according to the instruction manual the part number for the drum is KX-PDM4. But when I have done online...
Jim . That part number appears to be the right one . . We just cleaned out a large lot of odd and ends . . There was quite a few Panasonic items.......... . ...
Yep, yep and yep. ... From: printerrepair@yahoogroups.com [mailto:printerrepair@yahoogroups.com]On Behalf Of Don Backman Sent: Monday, October 03, 2005 12:15...
I had to change the DC controller, HVPS and LVPS. After that it worked fine. joe979xx <joe979xx@...> wrote:I replaced the fuser and that didn't fix it....
The top cover latch and the rear door are set on top of the machine.. Sometimes the top cover gets slammed and creats an issue. Remove the top cover and ...
If you turn the printer upside down you will see a spring on the right side of the DC Controller it is most likely disconnected. thats why you get a fuser ...
Replace Dc Controller ... http://us.click.yahoo.com/cd_AJB/QnQLAA/TtwFAA/67folB/TM ... __________________________________ Yahoo! Mail - PC Magazine Editors'...
I look after quite a few 8100 and 8100 printers. I have one customer with over 30 of them and several with over 2 million pages on them. What I've noticed on...
I look after quite a few 8100 and 8100 printers. I have one customer with over 30 of them and several with over 2 million pages on them. What I've noticed on...
2 MIL on an 81xx series printer is just broken in. I do work for a major bank's mortgage offices throughout KY and most of them have the 2k tray 4 - they wear...
I was curious about this fix and happen to have an HP 4500 in the shop so I played with the gear on the left outside and bumped the lifting cam levers up and...
Hi everbody, I have several HP 9000 printers that have had this problem off an on. What is happening is the paper exit flag in the fuser ass'y sticks after...
Hi Group, I having problem regarding HP 5000n printer. Printing problem - prints gets cut horizontal. I have confirm Fuser Assembly, Scanning Assembly, and...
Hi all, Got a problem with an HP LJ 9000. The original problem was the fuser roller film was torn. Transfer roller was about 50%, page count of 213K. Installed...
hello did you try to changes the fuser unit???.......try to replace new one..... bye ... Yahoo! for Good Click here to donate to the Hurricane Katrina relief...
prints appears only @ starting areas only ( 30 / 40% only ). Note: forwarded message attached. ... Yahoo! for Good Click here to donate to the Hurricane...
I have tried the following per help from Xerox - Drum heater relay board,electronics module, and new drum, and none have solved the problem. Now they suggest I...
Gravity must be especially powerful lately; causing a brain drain. First: HP2000c, has anybody seen the deaded stuck 'bongo pads' on this printer? I have one...
The transfer roller came to you in white material, or turned white from use? ... From: printerrepair@yahoogroups.com [mailto:printerrepair@yahoogroups.com]On...
The 4250/4350 reset is slightly different than the 4200/4300 Turn printer on When the memory starts counting push and hold the checkmark button until all three...
techsupp
techsupp@...
Oct 5, 2005 2:40 pm
18831
c00159101 is the TWI doc - finally shows the ground spring mis-location that causes the weird problems. Hmm me wonders why this is a TWI and not a service note...
Dear Friends, Hope I am not getting out of the line. Please does anyone have tips on this Olivetti Copia 9910? I went to try my hands on this one and I need...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
