Sounds like a memory error. Power down and remove the memory simms and power up. Add one and go through the procedure until you find the culprit. Jim bcoes ......
Single sheet paper or multi part paper? Also does this have an auto gap adjust or manual? I've had Okidata impact printers and some heavy IBMs that I've had to...
I am looking for the procedure to reset the photoconductor counter for the Lexmark W840. I am also looking for a supplier for the DRUM (just the OPC DRUM) to...
53 is actually a laser malfunction - the laser scanner motor may be bad (listen for the scanner motor run up when you send a print or turn it on and it goes...
Are there any sub codes to this message, 53.xx.yy, where xx and yy = numbers? This is most likely a memory error. If it has optional installed memory, remove...
Chad; Tighten the Ultrex connectors on the DC Controller connecting the Laser/Scanner Assy. Bob ... From: Chad Hughes To: printerrepair@yahoogroups.com Sent:...
Chad Try this. ALL SERVICE ERROR 53 On the HP Laserjet 4L/4ML/5L this error is indicated by the data light on and all others off. 4L/5L 1. Error found in...
Thanks Bob I will try tightening the cables from LSU to DC controller. I have replaced the laser scanner also, got left out of my first post. Chad ... From:...
Have several HP LJ 4000 printers that keep having 13.1 paper jam errors. They print fine from tray 1, but will not feed from tray 2. I have tried different...
Jonathan, Start by looking in the printer where the drawer slides in. Look at the shaft with the half-moon rollers and manually give it a turn. All there? ...
One of two things on these - overfilled service station, or a crack in the service station housing. There's a felt pad in the bottom but once it gets full it...
It is a clutch issue. The clutch behind the separation roller is too tight. You can replace it, but I always just take them apart and removed 1/2 the iron...
Assuming you've tried different trays with known good rollers (as you stated) and the paper is attempting to go up but stops past the rollers, it's likely the...
Must be LJ 4000's week for failures - have 2 in the shop, one on he list for 13.1 and this one for slow printing. First thing I do on slow printers is reset to...
The part mentioned at Agson is list $63.00 at HP's parts and is available. RG5-2651-090CN Also if checking many suppliers leave the -090CN off, easier to...
Is it hooked to a Dell??? If you let Dell computers self install the printer, 400's & 4050's will run at 4 PPM. Install new drivers from HP.com & all will bw...
Also, check the driver it's using. PCL6 drivers on WinXP default to 1200x1200 dpi which causes the printer to print very slowly (8ppm). You can install the...
Jim O'Connell
joconnell@...
Jul 12, 2007 5:19 pm
22682
my printer is Canon i6100 and now this printer is blinking. How to reset my printer ?...
Were you successful in printing an engine test with this machine??? ************************************** See what's free at http://www.aol.com. [Non-text...
Media path error. Has anyone seen this error. Xerox was pretty vague. It seems like it has something to do with printhead wipers. If I try to send eliminate...
Anyone else have any suggestions on this error? The last thing I just tried was to swap out the DC controller and this didn't help either. The only other thing...
While we are on the subject of duplexing I also have an HP8150 that will not duplex without jamming. I have tried several different combinations of fusers and...
I have an Hp8000 that keeps giving me a 55.a error whenever there is a duplexer installed. I have swapped out the duplexer several times as well as the fuser...
Yes it can be a power issue . . Try to isolate this printer on it's own or with low draw items. . Years ago I had a 5Si that was on the same circuit as the...
I always remember the 8000's we had at my last job had lots of issues with the power supply itself. I must have replaced tons of those b/c they constantly...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
