Naim still put forward reasons why they continue to use DIN plugs. Anyway for those who aren't afraid of delving inside here http://home.jps.net/~shilohz/ is a...
Hello All :-) I am playing around with the following at the moment; one 33 split into two 303's (LL&RR) driving stacked 57's. The right 303 gets its power from...
Thank you ALL for all the ideas on cables for 33-303, I went for the lazy option,http://www.flashbacksales.co.uk/ I must say that I was more than impressed...
I bought a Pair of Quad II-Forties and the QC24 pre amp, three months ago. 1st I took the base off one to take a picture, I see that two 6 watt resistors are...
Lee, I have nothing at all against DIN sockets, I am old enough to remember the days that almost everything under the sun, was made with DIN inputs, and of...
Hello, Since the 405 is quite old, I would recommend one more upgrade. Please change the elcos in the power section (10000 mfd 65V) and replace them with...
Hello all:-) I spoke to David Laine of Flashbacksales today, Yes on a SUNDAY :-) And He sorted the problem in 2 minutes flat... ACE AGAIN ! Thank You All for...
Quote from Naim:- The typically capacitive high-frequency impedance of an RCA connector is around 200 ohms--a mismatch with the 50 ohm impedance of the...
Don't worry I have nothing against those that mod their kit. Lets face it you paid for it so do what you like. I have 2 pairs of Quad II's. One of which will...
The 22 used phonos, but why would a 70 buyer of a 405 not want a matching Quad 33 preamp? And by exension a Quad tuner. So I suspose DIN makes sense, but DINs...
Stephen Robinson
heiferboy@...
Feb 2, 2003 2:01 pm
1267
Dear all, For anyone interested, I've updated my review on hifidelity.tk; see ...
Arthur, We should also distinguish between using DIN plugs and sockets (like QUAD and Naim) and using the DIN standard. Philips not only used DIN plugs and ...
Hello Scouring eBay has turned up a number of 303+33 combos one 306+34 combo a few 405s and a few 405-2s I am leaning towards the 405, but as there are not...
Hmmm.. Sounds a bit over my head to be honest, But does that mean if you don't use a 4 core interconect, but two seperate shielded wires, as all my DIN to DIN...
Stephen Robinson
heiferboy@...
Feb 2, 2003 11:36 pm
1272
... nonsense! The head of Quad. The followed the link after my "teasing" comments? Or was the link dead?...
Stephen Robinson
heiferboy@...
Feb 2, 2003 11:40 pm
1273
Sorry, that should have read, did you follow my link... Which was: http://home.pacbell.net/drquad/rosswalker.rtf If it has disapeared I'll put it in the Groups...
Stephen Robinson
heiferboy@...
Feb 3, 2003 12:16 am
1274
It's a bit of a waste of a Mira. Also Quad 34's are dirt cheap & not as bad as the reviews & easy to find - I'm running one myself. I think just from a...
This isn't what STEREOPHILE thought! http://www.stereophile.com/showarchives.cgi?655:1 ... _________________________________________________________________ ...
It is many years ago now so my brain is a bit fuzzy, but the official Quad 3003 mono bloc mod required (I thought) a variable resistor(3 legged) on the input...
You should be OK with the 2 cables going to the one earth point in a DIN plug. ... From: Stephen Robinson Hmmm.. Sounds a bit over my head to be honest, But...
Arthur, From memory - I'll have to dig my books from the 1970s out to double check: The RCA standard uses a very low output impedance to drive a high'ish...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
