... power ... the ... Looking at my PS PCB (which I haven't fixed yet, but have all the parts, just need some free time) The ZD3 zener diode should have the ...
Thanks a million LC, that's the way round I guessed it was but it's great to have it confirmed. When I first soldered in all the parts and checked all the...
The diode is 1N4744 15V 1/2W The good site with info how to fix power supply in 715 is here: http://www.dvdboard.de/FAQ/new/raite/netzteildefekt.htm It is all...
Well, I'm happy to report that everything is working fine. I don't know why those +3.5v pins were reading -12v but it works. Rob ... I ... (for ... results ...
... I believe that the listed voltages only appear under load. With no load attached, those pins will 'float' high to the bias load, which appears to be 12v. ...
... Funnily enough, seeing as how I've got the player all opened up anyway, I figured I might as well upgrade the DRIVE and PLAYER firmwares while I was at it....
I am not actuallu sure what type of rom is in my machine(Raite 715) but with any blue (CD-R,CD-RW) the rom struggles like hell to read it. If i open and close...
... to ... Straight from Yamakawa's FAQ: (yamakawa.de): I have set my Yamakawa DVD-218 to "region code free" with a special remote control sequence. Now I...
Antonio Semeco
ASemeco@...
May 5, 2003 4:29 pm
4810
Hi, I saw that matrix. What is confusing is the Table heading shows DVD-218 but the page title shows dvd_player_205. Also the matrix from the US site (listed...
It sounds like it is most likely the power supply board. I had the same symptoms with mine and fixed it. You can read my info on how I repaired it here:...
criswilliam
woodward@...
May 6, 2003 4:50 am
4812
please keep me posted. i am in the same situation as you , Dell PC and yamakawa 218 vdprao <vdprao@...> wrote:Hi, I saw that matrix. What is confusing is...
Is there any special trick to upgrading the drive's firmware for my Raite AV715. I was going to do it using my XP machine but then I noticed that there isn't...
Crowe, Robert
Robert.Crowe@...
May 6, 2003 10:43 pm
4815
Hmm, well, I checked the PS board, and orange is outputting -12v, red: +5.10, and yellow: +17.8v. Hmm, guess yellow is running a tad ritch. C23 on the board...
Hello, Thanks for the answer, I have problem getting the right one cause i have opend my player and what i saw was interesting, i have a CS chipset and no...
Caps are cheap, just replace them. ·TechnoDragon· <tdragon@...> wrote: Hmm, well, I checked the PS board, and orange is outputting -12v, red: +5.10,...
The power supply problems will require replacing the following: ZD1, ZD3, C19, C23, C25, C24, C18 ZD1 replacement: 62v 1w (78-1N4759A mouser part number) The...
Gala, Kishor/DEN
kgala@...
May 8, 2003 3:32 pm
4819
ZD1 looks good (and is unmarked, nothing printed on it to indicate polarity!), but ZD3 looks funky, one end has a frosted white ring around it. Should I...
Forgot the specs for ZD3, but both ZD1 and ZD3 would need replacement. I replaced the two zeners and the five caps for ~$6. Change all at the same time. One...
Gala, Kishor/DEN
kgala@...
May 8, 2003 8:23 pm
4821
ZD3 is a 15V zener. If it is good, you should be able to check the current flow (undo one lead) with a VOM. Note the polarity and solder a new one the same...
Gala, Kishor/DEN
kgala@...
May 8, 2003 8:28 pm
4822
I just had to replace both zener diodes along with some transistors and a bunch of capacitors on my Raite AV715 as my power supply had completely died, and the...
I got a ZD3 and replaced it. But someone said that ZD1 was 65v, and Supertronix didn't have that value. Well, they did, but it was the size of my pinky finger....
... value. Well, they did, but it was the size of my ... On my Raite both ZD1 and ZD3 were definitely toast. ZD3 is 27v and 0.5w The NTE # is NTE5033A, the...
... On another post I was told it was 15v @ 1w for ZD3. Are /both/ ZD1 and ZD3 supposed to be the exact same value? -- _____ _____ _____ __ __ __ __ _____...
... ZD1 and ZD3 are completely different. I have loaded a spreadsheet to the Documentation folder that lists all the parts along with part numbers at mouser...
Can you tell me what the values of those parts are? My system cannot read .xls files, and I don't feel like spending two days downloading Excel or something...
... After much research, I've found that NOBODY has new firmware for the RDR-201H Drive......only the other models. Guess which drive my Raite has in it?...
Is there any info around on the RDR-201 drive? Do we know if it's different enough to the RDR-202 that the firmwares are not interchangable? You could use the...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
