Where can I find an assembled unit for sale in the US That can be used on 6 and 12 volt batteries? I just found out about these an hour ago. And this group...
Hi Condeeg, that means that that other newbie Nigel Dawson is a moron, a dork without manners, at least without good manners. But a tip for you, before asking...
Hi condeeg I hope you find the info you require Bruno's comments are a good guide to forum chat. Read loads first and then ask sensible questions. I'm nut in...
nigel dawson is what is known as an internet troll..they live to shock people ...it is their only pitiable form of entertainment...try this link on ebay..i...
apparently the link that i previously sent doesnt work..you can try doing a search on ebay for wizbang...or go to the website http://www.wizbangplus.com/.......
Condeeg, I wanted to refine, if I may, part of Bruno's note to you about where to type your replies when you do reply. Because, this is more a matter of "good...
Hello and thankyou to this group. After nearly a year now of lurking around desulfator boards and postings I am about to receive (should God and the New...
Hello spartakplutonium   If you feel you must, you should use a constant current charger of about 300ma. A constant voltage charger is not a good idea as...
... about 300ma. A constant voltage charger is not a good idea as it will put out it's max current until the battery voltage rises, and if it doesn't rise...
The photo's for this post are under 'Graham's' in the photo section. The Courtiestown kit is very good, it arrived somewhat scantly packaged for a 12,000 mile...
Are you saying that you have attached a 13.8V power supply to a lead acid battery with a shorted cell? Isn't that drying out your good cells? Is the battery...
Hello everyone, I have bought a few of the 555 timer circuits and a pic version from courier in the uk and have an issue. I shelved the pic desulfator for a...
Switching a FET for a bipolar transistor will make a huge difference in the circuit operation. Typically FETs are much faster & require less turn on energy....
Well I guess that's what I get for doing these kinds of things late a night when my mind is restless! D'Oh! Well I thank you for pointing out the blatantly...
I realize this isn't EXACTLY on topic but I feel it is in the spirit of desulfating. My question is where do you get your batteries to work on? Or more...
One way of checking an inductor for shorts is to dab it with a voltage from a low impedance source and monitor the waveform on an oscilloscope. If the ...
Rob, If you've taken out the original MOSFET it's likely you've damaged the 2N3904/ 3906's as well. Regards Richard ... it ... hot ... clamps. ... volts. ... ...
Thanks, but I've replaced both the MOSFET and the transistors already, only I have replaced the MOSFET with a transistor inadvertently and I don't have a...
Hi, I recently built a couple of PIC Kits from courtistown to fit to my Boat Batterys. It's a liveaboard with a 24v 190Ah system and a Stirling Charger/PSU The...
I seem to have solved the problem... I reset the trim pots fully clockwise and then turned them back slowly until the unit just started to oscillate audibly...
Rick/Robert In another forum I think you said you had a Charger/Pulser in the works. Is that still being worked on or should I just get the latest/greatest pic...
I don't know if you got an answer about this or not. My guess is the pulse is too long and this will saturate the inductor causing excessive current flow. When...
I have found that one can replace the fuse that comes with the kit with a thermal fuse (I use a 500mA PTC) and although it has about 1 ohm resistance, it seems...
Looking at the Couper design, there may be room for improvement. It is based on the usual boost circuit, but ... the larger inductor is just a soft start for...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
