What are you asking..$$$ ? ... ____________________________________________________________________________________ Be a better pen pal. Text or chat with...
If anyone is still left here using these antiquated but still very usable VM-3100 Pros with the Roland R-Bus PCI cards I have a question for you. I bought a...
... You don't need it at all. In fact, my two RPC-1's wouldn't sync at all with the cable connected between them. ... There is only one place to attatch the...
Ditto on the “don’t need the sync cable” thing. I had the same experience and the good folks are Roland were the ones that confirmed for me that I did ...
... Ok zoinky, thanks a bunch. I had tried it without the cable a while one night and it half way worked but plenty of bugs so I didn't try to trouble shoot...
... experience ... that I did ... order to ... documentation ... the two ... placement ... group ... not like ... is that ... unless the ... that I ... share...
Hi, all, A short time ago I thought my channel 4 preamp was fried (turned out it wasn't - a factory reset got all the lights flashing again), and I got to...
In my opinion there are two ways to look at it. First, if it isn’t broke don’t fix it. Meaning, if your current equipment is getting the job done for you,...
Hi, Tod, Thanks for your reply. To tell the truth, the factory reset (and cleaning the surface of the LCD screen..:-) did exactly what I needed - I had to...
I don't know anything about the particular products you referenced, but I do know that the mic pre-amps on the VM3100 are terrible and are probably the only...
Before I get into this, I'd like to specify that I'm not trying to start an argument, and the few points I'm going to respond to are sprinkled sparsely between...
In other words, how would one avoid the preamps and use the digital converters of the VM3100Pro to achieve maximum benefits. (Actually, as a fader control it...
... by ... VM3100Pro/RPC-1 as ... the ... As long as you don't turn up the knob right under the input you're not using the pre-amp ... external signal ... (the...
... digital ... (Actually, as a fader ... that myself, ... guitar is ... Well unfortunately they're always in circuit, the best you can do is turn them down...
Uh, what do you mean? If they are completely counter-clockwise, there is no signal in. Do you mean that the preamp "cuts in" at a certain level depending on...
I always turn off the cabinet models in all my hardware/software. Then, whether something is a head or a preamp is irrelevant in this context - the software...
I've GOTTA wait until I read all your posts before I respond.... As I mentioned earlier, I am micing my amp, not the guitar itself (The guitar goes into the...
I should mention that my PUTW pickup is mic level (unless I use their PowerPlug preamp, which is fine live, but I prefer not use it in the studio).... ...
Has anyone tried to use this with the VM? I have MidiQuest 8.0, but find it kind of buggy (either that, or I'm not doing things right.) There is a newer...
I don’t have a lot of time for more input here today (although it would be great fun, I miss these kinds of discussions), but I do want to give a little...
This makes a lot of sense, and is the best argument for keeping the VM3100Pro. I'm not actually recording (AD conversion) using the mixer, although it is in...
If the trim knobs are all the way down, you will still get signal through. Maybe not with a microphone or a guitar but many +4dBm (dBu? dB something) studio...
... the ... mixer, although it ... The only way you could be going into the VM3100 without using its AD conversion is through one of the SPDIF inputs, but the...
Oh, for pete's sake. Sometimes I go directly into the amp and record with the H4; sometimes I go through the GS-10 and use the GS-10's converters; sometimes...
... know how much ... reasonable ... It's never a good idea to put any amplifier at maximum volume, they're usually built to be most efficient at about 90%,...
I can't seem to get the phantom power on my VM3100 Pro. It worked up until recently. I haven't used the VM for about 5 months. Plugged it in a couple days ago...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
