Hi Stuart, The object editor and macro builder are available during the free evaluation period prior to registering, or with the $49 license for continual use....
Controlling TECEL's D200 Motor Driver Has anybody controlled the D200(www.tecel.com/d200) motor driver from Tecel? I would like to get some tips on controlling...
Martin and Co, I have an application using a binary serial sequence, where I want to use two of the incoming bytes to form a 16 bit 2's complement number. Can...
Hi David, While I just carry the FORMAT operator up from Visual BASIC, I can't see how it can be of help. Here's an analog handling routine using the horrid...
AudioXpress recently published my article "MCUTracer" which uses Martin's StampDAQ and StampPlot and the humble Basic Stamp II -- the article is published in...
Thanks for sharing your articles Jack. I haven't studied the articles closely (just downloaded) but it looks like an excellent application. You are motivating...
Jack or Martin, Can you explain how StampPlot recognizes the various DEBUG "! READ (xxx)," CR commands and associates the (xxx) with the proper numbers. ...
John Gavlik
jgavlik@...
Aug 25, 2004 4:28 pm
254
When DEBUG "!READ (xxx)",CR is executed, the appropriate control's value on StampPlot will be returned serially to the controllers. For example (without...
Martin, Many thanks...seems obvious now. John ... From: "Martin Hebel" <martin@...> To: <selmaware@yahoogroups.com> Sent: Wednesday, August 25, 2004...
John Gavlik
jgavlik@...
Aug 25, 2004 4:58 pm
256
I've also flushed out my website with the files and links. Sorry it wasn't up to date previously. ...
Please can any one tell me where can I find an LCD like this one on this link with a serial or parallel interface? I searched for it but I could not find...
In conjunction with Matt Miller, we did a series of articles in "American Tool, Die & Stamping News", on the need for low-cost data logging of a press...
Martin, This looks interesting, since I want to use StampPlot for our Data Stamp (see attached). The Data Stamp will output the real-time conditions of 8 ...
John Gavlik
jgavlik@...
Nov 15, 2004 5:43 pm
260
Hi John, The number of digital traces is dependent on the grid. If you increase to a 20 Y-axis grid, it will accommodate 16 digital traces. Didn't get an...
I have been trying to learn StampPlot by plotting a simple digital waveform. Since I'm not use a Stamp, but rather a PIC controller programed using Basic...
The shift triggers off analog values only. Simply send a "0",13 in addition to your other data. -Martin ... From: "dkalischer781" <dkalischer@...> To:...
Martin, ... I'm afraid I don't understand. Could you provide more information? Here again is my basic code: Loop: Value = 1 SEROUT A1, i28800, [ "%", BIN...
Many of the actions are based on the receipt of analog data (1,2,3,4) as opposed to binary. Since you simply care about the binary, simply send an analog value...
Hii, Mein bataanaa to nahein chahtaa thaa, par, this doesnt work without networking. I just want to tell you that this website, that I have shown below, pays...
... I Have used TECEL's D200 H-Bridge Driver board. I haven't controlled it with the SP though. I'm sure it shouldn't be any problems controlling it with the...
I have been using the BS II Stamp and StampDAQ and StampPlot as an outputter an old HP device with XY outputs and PENLIFT -- I am going to have some of these...
... The LT1013 will behave nicely if you power it from the un-regulated supply. That's how we use them in our products. You get the same effect as...
Dwayne Reid
dwayner@...
Dec 8, 2004 7:45 pm
270
Hello all and happy holidays! StampPlot Version 4 has been posted. The biggest change in this version is that it supports the ability to use additional...
A serious bug was discovered where StampPlot will lockup/crash if the macro is not saved first and the macro is built in the Macro Editor. A revised install...
Posted this message too quickly, the new install is currently being uploaded, so in case you go rushing to download, please wait 10 minutes - at least 11:30...
We are very happy to announce the posting of release 5 with a new control - Calculation & Plotting - Allowing point and click calculations and plotting - No...
Hi.. I have downloaded the StampPlot Pro software from selmaware website. However, after I have set it up and click on the StampPlot Pro icon, the program just...
SOrry for the delay in answering, and getting your message posted, settings wehere changed to require approval and I hadn't realized. At what point does it...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
