... I Have used TECEL's D200 H-Bridge Driver board. I haven't controlled it with the SP though. I'm sure it shouldn't be any problems controlling it with the...
I have been using the BS II Stamp and StampDAQ and StampPlot as an outputter an old HP device with XY outputs and PENLIFT -- I am going to have some of these...
... The LT1013 will behave nicely if you power it from the un-regulated supply. That's how we use them in our products. You get the same effect as...
Dwayne Reid
dwayner@...
Dec 8, 2004 7:45 pm
270
Hello all and happy holidays! StampPlot Version 4 has been posted. The biggest change in this version is that it supports the ability to use additional...
A serious bug was discovered where StampPlot will lockup/crash if the macro is not saved first and the macro is built in the Macro Editor. A revised install...
Posted this message too quickly, the new install is currently being uploaded, so in case you go rushing to download, please wait 10 minutes - at least 11:30...
We are very happy to announce the posting of release 5 with a new control - Calculation & Plotting - Allowing point and click calculations and plotting - No...
Hi.. I have downloaded the StampPlot Pro software from selmaware website. However, after I have set it up and click on the StampPlot Pro icon, the program just...
SOrry for the delay in answering, and getting your message posted, settings wehere changed to require approval and I hadn't realized. At what point does it...
Hi, My aim is to use Stamplot as a GUI to remotely control a vehicle with a camera / sensors. The vehicle has a BS2 / Bluetooth EB500. Data is sent via a PC...
Stuart, I'm a little confused, do you need to communicate to both the Stamp and Bluetooth? I have the EB500 and adapter, but to tell you the truth I've always...
Looking through the EB600 to EB500 section of the manual, and doing some quick tests with SP, it looks do-able, though there's a few hoops to jump though (the...
Hi Martin, I don't need to to communicate with the BS2 connected to the PC. I presumed I would need to, so the Stamplot and BS2 could work in conjuction with...
Yup, StampPlot simply sends/receives from the serial port. It could be a serial VOM, a GPS unit, or a bluetooth module. As long as we can get StampPlot to...
Hi Stuart, I wish I could test things out on my side. It's odd you are getting varying address values in, and don't have to connect manually as specified in...
Hello Martin, Feedback as requested....I loaded the BS2 with the example you suggested and ran it in conjunction with your macro. 1. No ID address was or has...
Martin, Managed to get this example working. Controlling a remote sounder on an Eb500 / BS2 without the need for a macro. (Only because I'm weak on macros) ...
Stuart, Ahhhh, yeah, 0-100 would have been a very poor frequency range. Good troubleshooting. As far as the ID and such, I'm just following what the embedded...
Stuart, Good to hear, I guess nothing specialized on the StampPlot side is required. Now picture this: You walk through the factory with your laptop. As you ...
Hi, I am having trouble with constructing a slider. Initially to test controls via bluetooth I am using servos on the recieving end. Min Centre Max Ideally I...
Hi Stuart, Not doing anything wrong, you found a bug. It appears that when you try to set the minimum (500) above current maximum (100) it throws an error. A...
Hi Martin, Thanks for your reply. I to had just made a work around, when I saw your mail. (I didn't fix the slider but the output value to servos scaled OK) ...
Hi Martin or anyone, I would like to use an "Emergency Stop" button on a GUI. How do I change the following button to a red colour please. (I have trawled...
Hi Stuart, Sorry I didn't see this sooner. A command button cannot be made a different color. It's locked in. An option would be to use a label instead, which...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
