SESUSA members (that's you) are invited to visit our YahooGroup homepage, and click on the Database link or go directly here: ...
sesusa@yahoogroups.com
Apr 1, 2004 10:39 am
5656
Is anyone familiar with data comparing the relative efficiency at converting solar energy to electricity of a stirling motor driving a dynamo with an array of...
Alan, Are you looking for solar conversion eficiency or cost effectiveness. Dish systems are much better at converting sunlight to electricity for a given...
... From: Tom Gentry To: psymundsaltEnergysite@yahoogroups.com Sent: Wednesday, April 07, 2004 9:10 AM Subject: Re: [psymundsaltEnergysite] Ringbom's anyone? ...
Tom, Your points are well taken.....but.... Chuck is not asking a high efficiency, compact size, or low weight. As I recall from Organ's account, Rev...
Hi all, In fairness to Tom, Rick, I have to admit I DO want a 5-10 hp unit and his indications would seem to point to the fact that as the size of the...
Hi Tom, I gott'a ask how does one maintain pressure of Hydrogen when the monoatomic "molecule" is so small that it passes through the finest of grained...
... effectiveness. The first. i.e.; which option will charge the batteries faster from a solar collecter of 8 square meters on top of a campervan driving ...
Alan: I am getting along in my years but I do remember an article published in either the Science Digest or Science News Letter in the mid fifties IRT an...
The flat plate PV panels because they do not need to be aimed precisely. Tom ... From: Alan Sammons To: sesusa@yahoogroups.com Sent: Wednesday, April 07, 2004...
Are the system pressure values so often quoted room temperature pressures, maximum operating pressures or average operating pressures. If the pressures are...
Steve, Take the pressure at the cold temperature (ambient ?) and with the engine cold and multiply by the calculated pressure ratio. Or you can assume all the...
Does anyone have information about vehicles with Stirling engines and thermal accumulators (LiF,LH) as the main energy source. The Philips company may have...
This is described in "The Philips Stirling Engine", pages 320 to 324, titles "Rechargeable heat reservoirs". Numerous technical papers have been written on the...
Reading the following:- http://www.livesteaming.com/articles/hot_air.html I was intrigued by the use of pumice sanding block material to make the displacer. It...
I use a material called 'GrilBrik' for displacer pistons. This material is basically foamed glass. It is 'closed cell' The 'Sand-no-more' is another version....
Thanks, Again no google hits for UK but the similar Grillstone appears to be available over here (I was beginning to wonder if we cleaned our grills at all!). ...
The SESUSA list has been under an invisible attack for several months and although the enemy has not yet breached the gateway the volume of attempts is...
Folks, I'm having Yahoo look into the reason why I can't do direct e-mail replies to the message posts from the groups I own / moderate. This has been going on...
Hello, Last week, I sent a test message to myself and it worked fine. O then tried to send a message to someone else on a different group, and the message was...
SESUSA members (that's you) are invited to visit our YahooGroup homepage, and click on the Database link or go directly here: ...
sesusa@yahoogroups.com
May 1, 2004 10:58 am
5679
Hello, I am looking for alternator design assistance. I will be working with a 3-5 inch LTD, and designing a linear alternator to fit. I will use super...
Im new to the group and the idea of stirling motors. i have a idea of using a plastic 5 GAL. paint bucket to make a displacement type stirling, styrofoam for...
Bob From your post ... I don't think there is any possible way to build a multi-phase linear alternator that is directly attached to a single reciprocating...
Lee et al, Actually I believe you are quite wrong on this one Lee. It is easy to imagine that the three phase power of which he speaks is separated by 120...
John et al, Well, lets think about it a bit. We would have 3 magnets labeled A, B, & C spaced along a single (lets assume horizontal for the moment) rod...
Lee, Since et al seem to be be keeping quiet I will address only you for now until they chime in. There is at least one way out of this, albeit a bit messy. I...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
