SESUSA members (that's you) are invited to visit our YahooGroup homepage, and click on the Database link or go directly here: ...
sesusa@yahoogroups.com
Oct 1, 2005 4:49 pm
6660
So what does this have to do with the design and construction of Stirling engines? ... http://us.click.yahoo.com/dpRU5A/wUILAA/yQLSAA/UIYolB/TM ... === message...
It doesn't. The message and the author have been ushered from the list. Tom ... From: Tom Strickland To: sesusa@yahoogroups.com Sent: Saturday, October 01,...
I don't want to understand I just want him gone. It seems that everytime I think I am being to tight with the admissions standards one of these guys pops up...
SESUSA members (that's you) are invited to visit our YahooGroup homepage, and click on the Database link or go directly here: ...
sesusa@yahoogroups.com
Nov 1, 2005 7:32 pm
6666
Hi Would like to contact someone in Australia. Anyone there?? John Pietila Brisbane Qld ... From: <sesusa@yahoogroups.com> To: <sesusa@yahoogroups.com> Sent:...
... From: pentti37 To: sesusa@yahoogroups.com Sent: Wednesday, November 02, 2005 5:47 PM Subject: [sesusa] Finding a contact in Australia Are there any...
Hello John, My name is Harry Diers, I live in Tasmania and am always glad to find others with a similar interest in Aus. I have been building Stirlings for 18...
hi i am one of the guy intrested in stirling engines.... keep in touch ..... pentti37 <jpietila@...> wrote:Are there any 'Aussies' on this site? Regards...
Austalia nice!!!!!!!!!!! Im interested too, i have a little one from www.stirling-tecknic.de , the biggest interest if for solar energy in my case. ...
For any of you that know fluid dynamics. Could a regenerator possibly be made more efficient if the gas was caused to spiral (vortex) within the regenerator....
Hi I live in Australia. James ... From: <sesusa@yahoogroups.com> To: <sesusa@yahoogroups.com> Sent: Thursday, November 10, 2005 11:02 PM Subject: [sesusa]...
James, We have used a system to increase the contact of the hot/cold gas within the regenerator to improve performance. The basic problem (which I believe you...
Hi Harry, Sorry for my late response. I have been tied up with too many demands for my time. I am new to this type of engine .... consequently have done no ...
... is ... the ... will ... California ... from ... bottom ... elastic ... so ... changes. ... plate ... breakfast, ... are a ... might ... be ... with ... ...
Hello Mark, You have put forth a challenge for the members of this list to design a (solar?) power source generator. Your angle is that it can manufactured...
Hello Mark, James, Thursday, November 10, 2005, 9:17:57 PM, you wrote: MP> James, MP> We have used a system to increase the contact of the hot/cold gas within...
Higher pressure or higher velocity? My intent was not to create a true vortex with a pressure drop at the core, but was to cause the gas to have a greater...
James If the gas is to travel a greater distance in the same volume, it stands to reason that it must travel faster over a smaller cross section flow stream...
Hello James, In regen, sequence is important. E.g. when gas heats it must first face with cold part of regen, then with hotter, yet hotter etc. It garantees...
James, The question should be easier to visualize if you think in these terms. What are the conditions at the entry and exit, and how long and how far did the...
Folks, I asked Allan Organ a "similar" question a few years back. Is there any benefit in spinning the displacer about its longitudinal axis in a Stirling...
I have a 2 cylinder air compressor that I want to make into a stirling engine. My plans are to build a regenerator, and plumb it between the opposing...
Tim, You should start here. http://www.bekkoame.ne.jp/~khirata/academic/simple/simplee.htm By entering the values for volumes, pressures and temps, you can get...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
