siteplayer : Messages : 3537-3566 of 6359

Messages: Simplify \| Expand (Group by Topic)		Author	Sort by Date

3537	Check that you have 12 volts where the power enters the development board. If you have 10.50 volts the zener D7 will drop the input voltage to the 74HC86 pin...	dholland91505	Apr 2, 2003 1:46 am
3538	One other thing. If you measure the voltage on the 74HC86 pin 5 as noted below, be sure to use a high impedance volt meter otherwise you will get 3 volts or...	dholland91505	Apr 2, 2003 1:59 am
3539	What are methods for programming the siteplayer in production (ie. without the development board.)...	timsjob2002	Apr 2, 2003 5:08 pm
3540	Once the DHCP has assigned the siteplayer an IP address how is that IP address known to the user, so he can access the website....	timsjob2002	Apr 2, 2003 5:08 pm
3541	You have to use Serial Tester and be connected with a serial cable. It will tell you the I.P. address. ... From: timsjob2002 [mailto:timandcathy80@...] ...	Kirt Boynton kirt_boynton	Apr 2, 2003 5:25 pm
3542	You would need a processer connected to the serial port of the SitePlayer. It would use the ReadX command to read addresses 0FFE6 through 0FFE9 which contain...	dholland91505	Apr 2, 2003 6:10 pm
3543	You can program them when they are installed in your target application device as long as you know their IP address....	dholland91505	Apr 2, 2003 6:13 pm
3544	Hi Group, I have 2 linkSys routers sharing a single DSL line with 2 public IPs assigned by my ISP. My siteplayer is on one of the 2 routers. For a while I was...	sp4jz	Apr 2, 2003 7:16 pm
3545	There is also a utility called SiteFinder that runs on a PC on your LAN, and polls each IP looking for a siteplayer. It returns the IP when one is found. ... ...	John Remington jrem123	Apr 2, 2003 7:51 pm
3546	Check the DMZ host setting in the router, it will override the port forwarding settings by forwrding all ports to your PC. Also there is an option in the...	Ken Brown imems2001	Apr 2, 2003 9:06 pm
3547	At last, we received our production run of RJ45 mag jacks for the Siteplayer. They are available from our website www.pca.com/onlineshop in small quantities....	Ben Weinberg ben+weinberg	Apr 2, 2003 10:20 pm
3548	Ben, The link for the datasheet is incorrect. It ends "gif" instead of "pdf" Keith www.diyha.co.uk www.kat5.tv...	Keith Doxey keithdoxey	Apr 2, 2003 10:28 pm
3549	Thanks. But - 1. My DMZ host is not setup in my router. Since you mentioned it I had just set up one and tested pinging and port forwarding - it didn't make a...	sp4jz	Apr 2, 2003 10:38 pm
3550	Keith: Thanks for the heads-up. It's fixed now. Ben...	Ben Weinberg ben+weinberg	Apr 2, 2003 11:59 pm
3551	HI all, Just enquiring about how to poll the siteplayer from a VB application to see if the siteplayer is 'Hung', and if it is how do i resest it??? Thanks ...	Chris wittfield2000	Apr 3, 2003 12:46 am
3552	RJ45 also available at www.totalrobots.com Total Robots Ltd www.totalrobots.com ... From: "Keith Doxey" <ukha@...> To: <siteplayer@yahoogroups.com> ...	John Taylor totalrobots	Apr 3, 2003 1:08 pm
3553	here is a really stupid question, but do you have the sitplayer on the second router, i.e., DSL -> Router -> Router-> Siteplayer? I'm asking because a) I...	John Remington jrem123	Apr 3, 2003 1:49 pm
3554	My 2 routers are in parallel, not serial configuration. They each have their own public IP address and are independent from each other from a network point of...	sp4jz	Apr 3, 2003 3:14 pm
3555	Dear Sirs, I have a problem using the site-player-dev-board: Attached you will see my "download service program" If I run it, comes response: No response From...	Leonardo Moreira Alves leo_alves	Apr 3, 2003 10:42 pm
3556	In page 29 from SitePlayer_Software_Manual.pdf you say: WARNING: Do not perform serial port I/O to the SitePlayer during Ethernet downloading of new firmware,...	Leonardo Moreira Alves leo_alves	Apr 4, 2003 1:09 am
3557	Hello, To monitor the coming data from serial port on a web page, I would like to know how to refresh a text area or a frame. I tried auto-refresh the window...	wuyinghoo	Apr 4, 2003 5:07 pm
3558	My experience has been that the SitePlayer goes stupid until you use the Rescue function in the Serial Tester program to get it working again. ... field, you ...	dholland91505	Apr 5, 2003 1:19 am
3559	I made a study and I am getting a 10.5 V from the adapter to the siteplayer. I am creating a power supply myself to provide a 12v supply correctly. I also...	K.T.Kumar kumar_kt	Apr 5, 2003 4:37 am
3560	I tried my custom designed 12V power supply. I also made sure that the voltage is around 4V at pin 5 of 74HC86. One of my two siteplayer module works !!! I am...	K.T.Kumar kumar_kt	Apr 7, 2003 11:06 am
3561	Hi all, Just a quick note to ask if anyone knows when the interanl language will be available for use?? Thanks Chris...	Chris wittfield2000	Apr 7, 2003 12:47 pm
3562	Chris, Most probably never. It's been at least 1 1/2 years so far that it's been promised... Ken ... [Non-text portions of this message have been removed]...	Ken Campbell thetoasterboy	Apr 7, 2003 12:53 pm
3563	Do you know how to run the rescue function in the Site Player serial tester program? ... [Non-text portions of this message have been removed]...	Leonardo Moreira Alves leo_alves	Apr 7, 2003 5:05 pm
3564	To run the rescue function in the "Serial Port Tester" program, you would first make sure the correct COM port is selected by clicking on the "Comm" menu item...	dholland91505	Apr 7, 2003 5:46 pm
3565	That is great news! Not sure why you were getting 10.5 volts from the power adapter. That is way too low. Mine measured 11.98 volts. I don't know why they...	dholland91505	Apr 7, 2003 5:59 pm
3566	... I see this also, try a different IP, I have a collection of modules that will for example work at 192.168.1.6 but not at 192.168.1.5.. or another that...	Graham fg8mbi	Apr 8, 2003 6:35 am

Yahoo! Groups Tips

Did you know...

Messages

Yahoo! My Yahoo! Mail
	Sign In New User? Sign Up
		Tech - Groups - Help

Yahoo! Groups Tips

Did you know...

Best of Y! Groups

Messages