The Siteplayer dev board schematic may be what you're looking for. http://www.siteplayer.com/docs/001212/SitePlayer_Devel_Board_schem_2003.gif Hope it helps. ...
i have try to connect a SitePlayer Telnet module with a Basic Atom Pro but not comunicate. I have shaped IP address of the SitePlayer, possible several the ...
Hello :> I was hoping someone could help me understand how to set the SitePlayer IO to read only I have constructed a circuit which takes in temperature...
... Only 32 different values are possible if this is a parallel interface. Care to give us a hint as to what temperature sensor you're using? Are you sure...
I haven't used the I/O as inputs, but it looks to me like the internal pull-up on the Phillips chip makes the I/O tristate, so you should be able to put a...
Thanks for the repsonses ...It seems I was just examining the wrong places Sorry Just to answer some questions I'm using a LM355Z Temperature Sensor with...
I have the same project as you (LM355Z & ADC0804), and the same definition structure, but I'm not able to get further than Linker error unknown command $ d. ...
I'm at a loss here. I've been using S/P and Sitelinker for almost 2 years and never had this problem. When I try to make a download file I keep getting the...
... almost 2 ... file I ... \SAVEDFILES\misc\deffile. ... on the ... Area** ... Thanks for the reply Rusty. That missing underscore was a Typo on my part...
Hi Does somebody used a weeder board controled by siteplayer, when i read what siteplayer is sending with the computer i get "AHA" so it is correct, but when i...
I'd like to configure a "stay-alive" function for the SP from my micro which happens to be a SX28 from Parallax. The micro would reset the SP if the SP ever...
Hi Kevin I've a couple of little systems fitted with SitePlayers. They work since many years without having been disconnected but once, last summer (I...
I can add a little info to this thread, not much, but a little. I recently purchased the SitePlayer so I could create a webpage from which I could remotely...
... 1" .... ... There are some small differences in the version 1 and version 1.1 instances of the hardware but you'd be better off if you got both pieces of...
Scan back in the group and you will find some details on issues where the router uses a certain chip to provide the ethernet switch, one of which causes...
I have a custom PC carrier board I developed for my siteplayer project. I leveraged the schematic of the latest netmedia development board to get me started....
Hello, it is possible to display the MAC address of the siteplayer that I am linked on and how do I make it possible with the ethernet link only (not serial)? ...
I am looking for either an example of a piece of code that basically communicates over TCP/IP, or someone who can give me a pricing on a solution. I have...
Hello, I wonder how to change the default port 26481 because I need to install 4 Siteplayer on my router and I will be able to access them by the internet. (...
If you include UDPSend_Def.inc in your siteplayer definition file you will then have names for the 6 mac address bytes in the siteplayer and can do normal...
WebBrick is probably a bit of overkill but it sends out UDP packets when its inouts change. www.webbrick.co.uk Manual and data sheets under Downloads....
... Yes, it is possible. Add this to your .spd file: org 0ffe0h mac0 dhex 0 mac1 dhex 0 mac2 dhex 0 mac3 dhex 0 mac4 dhex 0 mac5 dhex 0 And then use...
... I'm not absolutely sure I understand your question, but here goes... Using Port Forwarding configuration setup on your router, assign a unique Port number...
Yes, there is a huge groundplane that I removed to make for a better picture. I think it is a powersupply issue, actually. After a little more checking I...
NO. Our experience is that siteplayer very sensitive to power fluctatuations. Needs to be above 4.75V. I suspect the CPU has brown out set to reboot the chip...