Hy to All. I need a some help to show a RAM byte variable of the Site Player in my HTML page. I have the line below in HTML: The flow rate at this moment is...
... Sure, see page 14 of the "Siteplayer Software Manual" under the heading of "Selecting a Particular Digit of an Object". Funny, 'flow' is the same variable...
... Leonardo; Enter the ^flow Site Object in your HTML code like this: ^flow:3^^flow:2^^flow:1 This will display the Object's decimal digit values in order...
Hey Folks, Has any one here been successful in interfacing the Siteplayer with the JDS made "Stargate" Home Automation system? I tried outputting serial text...
This is my first siteplayer webserver - it is connected on to the network I use with a fixed IP address. It is working on the network with the default factory...
Is your "port address for download" set for 26481? Is your $InitialIP definition (in the .spd file) match your existing IP address? New siteplayers are shipped...
... Thanks for your reply - I had tried various ports 80 26481 etc and the IP had been set to my fixed address. So today I tried again with my files and the...
... Just tossing up thoughts in hopes of finding clues: Can you still ping the device? Is the device visible (IP/MAC) in your router setup/info screen? Is the...
... zero out ... Hello Marc - and thanks for your reply sorry meant to say previously that I cannot now ping the device I have a dedicated IP address tied to...
... existing ... and the ... either. ... the IP ... Hi Derek, There are functions available in the Serial Port Test Program that will reset or rescue the...
It sounds like a bad cat 5 cable or connection. Replace the cat 5 cable, re seat everything . Make sure the rj45 connections are fully locked, siteplayer is...
Hello, When sending objects of my control to SP1 via UART data will be initially transferred to the site. After a certain time freezes the website of the...
... Two suggestions: 1) Make sure the ObjectADR is in the range 0-255. If outside that range then use the $91 command. 2) Move the sending of 20 NULs outside...
Thanks to both of you for your assistance - I can now reliably download the compiled .spb files of my own and the factory demo default one without a problem...
... the ... that ... milliseconds. ... you've ... serial ... at ... Thank you! I think the SitePlayer module has an error. When i start my session it works...
... hangs ... ethernet ... off the ... when it ... module? ... VCC = 4,9VDC. On the regulater is also connectet my AVR + LCD and it works fine. Tubie88...
... You're certainly welcome Derek, but I'm stumped at this point. There isn't any special setting for holding the program - once successfully loaded it...
About the only things that come to my mind, what's left of it... :-) 1) Power supply is not supplying sufficient current/voltage during the 'flashing'. 2) If...
Again thanks for your interest in my problem - I do have the netmedia development board running from a 12v 1A mains block which I will replace with a lab type...
... Kevin Yes indeed it does - I have just had the unit running for the last couple of days without any hint of a problem. I have just read your email and so I...
... I hope this wasn't NetMedia. If not, I'd try another supplier if possible or direct from NetMedia. I've gotten several units, 1 from Netmedia direct and...
My latest theory on your problem regards a series of posts here on this forum mentioning router and/or switches that aren't compatible to the SP. IIRC, it was...
I don't know the protocol for JDS but you can only send 16 characters at a time from a GET method. If the JDS requires more than 16 characters, you will have...
... characters ... it ... make ... using ... shifter. ... with ... is ... rs232 ... sent... ... Thanks for the reply. I can verify (using a simple comms...
... Many thanks to all who have responded and I apologise for the delay but owing to personal issues this project has taken a back seat. However I can report...
Is there any way to send an http request using the siteplayer? I know it does UDP outgoing packets, but is there a way to send a simple http get request to a...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
