... characters ... it ... make ... using ... shifter. ... with ... is ... rs232 ... sent... ... Thanks for the reply. I can verify (using a simple comms...
... Many thanks to all who have responded and I apologise for the delay but owing to personal issues this project has taken a back seat. However I can report...
Is there any way to send an http request using the siteplayer? I know it does UDP outgoing packets, but is there a way to send a simple http get request to a...
... No. UDP only for sending from the SP. ... Unless you need the web server capability of the SitePlayer Server then I'd suggest the SitePlayer Telnet for...
Greetings I am about to build a cable to connect a SitePlayer Telnet to a PC. Since they are both DTE devices with male connectors I assume that I need to...
... Hopefully this is for exercise as you can easily wander down to your nearest "Best Buy" or "Radio Shack" to get a 9-pin NULL MODEM cable and a 9-to-25 pin...
On Mon, 12 Jan 2009 11:03:27 -0600, you wrote: Rather than use adapters I would prefer to use a single cable, 25 pin female to 9 pin female. Earl J. Morris...
Am trying to interface a parallax passive infrared detector to siteplayer. Tried it out first with their BasicX chip, connecting the signal lead directly to an...
I just purchased a new siteplayer module, and cant get it to pickup an IP. It is getting link on the router, but doesnt appear to be getting DHCP when I check...
... Get the SitePlayer Development Manual here: http://www.siteplayer.com/docs/001212/SitePlayer_Development_Manual.pdf As shown in the diagram on P.7, use a...
Marc, I couldnt locate the parts for the serial convertor readily available around me, and ordered them offline. In the meantime, I found this diagram, which...
I Have some doubts about the 7404 with series resistor being reliable. Here is a simple circuit that you might want to try if a Max converter is not...
You're welcome Jason, The problem is that valid RS-232 signals are plus or minus 3 to 15 volts. Logic one is defined as a negative voltage and logic zero is ...
Thank You for the help! I got serial working on this using the serial_converter.pdf file in the files section - 10 small components and a bunch of jumpers and...
You're welcome, The Ethernet magnetics and filter are necessary for isolation, impedance matching, and noise filtering. They're necessary for compliance to...
Hi All, I have just joined this group. I am an embedded hobbyist. I can work with PIC microcontroller.I want make a project using which i can send/receive data...
Which SitePlayer module to use depends on your application. SitePlayer SP1 will send and receive TCP/IP data through a web browser interface with textboxes,...
... work with PIC microcontroller.I want make a project using which i can send/receive data to my webserver. Please advice on the module to start with. And...
OK - I recieved the LF1S022 magnetic RJ45 filters from Netmedia, and still cannot get my device on the network. I have tried using them with the following...
On Mon, Feb 16, 2009 at 9:51 PM, jasonhershkowitz ... Hello! Ideally the schematic drawn by Professor Igoe should be the same as the one which Netmedia...
4,5,6,7 should not get you a thing as the wiring is invalid for Ethernet. What are you connecting Site Player to? In which direction are you getting a link...
Siteplayer is connected to the ethernet transformer (sold by netmedia), and then connected to a d-link router. I can get and set the IP using the serial cable,...
All of the carrier boards that I have made use the same pin connections which I copied from the SP1 development board manual using a LF1S022 (no lights). The...
I should also note that ethernet uses pins 1, 2, 3, and 6 on the RJ45 connector but the LF1S022 makes these connections internally. If you look at the...
If you can find someone that has an old USRobotics modem, these have the cable you are looking for ... 9 -> 25 pin. Any good computer shop will have these also...
Hello! Back when I first got interested in the concept of "embedded anything" (which is really a buzzword describing the idea of putting a whole computer into...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
