Thanks Russell, I found that SyncWizard works in a similar fashion to pass files in and out of my PDA. However, there is a glitch with SyncWizard that I have...
I bought a M500, installed SP (1.9.8-28MAR04) and sync it with a Belkin Universal Palm USB / Serial hotsync cable. To be sure that I have a clean install, I...
hi Mark, i am at the longmynd at the moment using sp in anger at last. i have shown the setup to the troops and they are surprised that they have not heard of...
Jock, First, the fatal error alert. As I put out in a couple of previous emails, the version you have had a change to the task data structure so the Task...
After some playing with the MinSnk info on the polar page it seems to me, that the info is displayed in metres per second instead of km per hour. Mark, please...
skyraider9999, What values are you using and what results are you getting? What results were you expecting? If you give your three point values (speed and...
Hi Paul, For VSO10 (club class, approx ASW15) I'm using following values 90kph/-0.693,121/-1.129,153/-2.060. L/D is 36 at 92kph - perfect, MinSnk:21kph -...
I have been using an M500 for the last couple of years with SP and have experienced the same problems with the last two releases of software. What happens is...
Mark, I have been optimizing the speed of SP on my M500 by using simulated IGC files replayed to the PC serial port via SeeYou. Like SOTS it has an NMEA output...
Russell, Unless your IGC file is set to record all of the GPS 1 second NMEA updates, a program to replay the IGC file as a NMEA stream will also suffer from...
Mark, I finally got the 302 to accept the declaration. I am curious why you have to set the data transfer type to serial and 4800 baud. Wouldn't it be simpler...
Paul, Thanks, I also use 4 seconds in my logger in the glider. But the simple test files I use are 1 second. I will try SOTS if that smoother. Again, thanks ...
John, The NMEA setting is for receiving NMEA data. That is what the 302 uses to put out NMEA data. However, when you are sending task declaration and other ...
Russell, No matter what interval you use to record the IGC file, SeeYou puts out the NMEA data at a rate consistent with the playback rate. So if you are set...
Marks, Many thanks, have been running at X1 with 1 sec files and it is OK. However, will try SOTS. re' chit chat on M500 serial I/Os :- my problem was caused...
Mark, Many thanks, have been running at X1 with 1 sec files and it is OK. However, will try SOTS. re' chit chat on M500 serial I/Os :- my problem was caused by...
(message repeat) Hi Mark! I know this is not a common problem, but in Israel we have several important waypoints - a couple of airstrips below sea level. The ...
Uri, Sorry I meant to answer your email before. A negative altitude is technically not a problem. It's probably just something in the UI code keeping it from...
Thanks Mark, I'll wait till you get a chance to fix it. BR, Uri ... <http://rd.yahoo.com/SIG=12ce8u2kj/M=290828.4794622.5939935.1261774/D=egroup ... ...
Hi Russel, I found out that the "problem" with the M500 is at the moment I start SP with the Universal Cable allready connected. If I follow the procedure of: ...
As a newbe to Soaring Pilot I have a simple question which most likely has an obvious answer but I have not be able to find it in anything I have read. I have...
Stan, You will not see the selected waypoint on the final glide page until there actually is data being received from the GPS. However, if you look at the ...
Thanks Mark, Once again, very helpful. Also, I loaded the new Beta version of the software to give it a try. I noticed thet the SUA information and the...
Edwin, There is no reason, at least within SP, that it matters which order you turn on the cable and/or start SP. I do both all the time with my m500. I'm ...
Stan, I do not understand what you are trying to describe. What do you mean that the SUA info and waypoints come out of sink (I'm sure you mean synch, right),...
Hi Mark, Yes of course (synch). Ops! Anyway here is what happened: a.. I have a m500 and installed 1.9.8 b.. Our field is located to the northwest close to...
I just downloaded an IGC file to my Mac. I have a Palm T-3 and a Garmin 76S with a synch cord. How do I get a graphic presentation of the flight, either on the...
Jack, You're probably not going to like the answer but it might be easier to run a windows emulator and run one of the windows programs such as Flight Display ...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
