Hi, I'm thinking about updating my hardware to get some more speed and to get rid of all those cabling issues. Therefore i was thinking of a Tungsten T5 in...
Andreas Lenz
Andreas.Lenz@...
Aug 1, 2005 7:14 am
4117
I use a Bluetooth GPS Haicom BT405. Very happy with it: long battery life (up to 10 hours), no need to have a connection to the on-board battery I have also...
Andreas, I have been using SP in conjunction with a Colibri and Borgelt B50 (I run the output from the Colibri through the B50 to the palm) this works well...
Andreas, After reading some other posts on this subject I should add that the BT338 has a 15hour battery life - tried it, manufacturers claim holds up on that....
Is SP possible with nmea Ver 3 used by etrex vista. I have no connection with etrex vista in nmea mode then by opposite I have no problem (connection and...
Joel, No I don't think there is a problem with the etrex using NMEA V3. I have used SP connected to an ETREX. I just looked at the manual of the Vista and it...
Hello - I have been setting up the Ventus B that I have been flying to accommodate my palm 505 driven by my volkslogger through a Goddard PS 5A conversion...
Hello All, I have connected my Lowrance 100 serial output (9 pin connector) to a Visor hotsync cable (unpowered) through a gender adaptor and null modem...
Last week I've enjoyed a short soaring holliday in Bad Berka, Germany. The weather could've been a little better, but what can you do? Anyway, one of the good...
Jim, Yes, you will probably need one of the powered cables from PN or other similar places. The problem is that the Visors don't have true RS232 ports. So a...
I'm not sure about your problem with the turnpoint and FGA display. However I would suggest to your friend to try the latest 3.0 beta from the yahoogroup. I...
Antoine, What altitude mode did you have? (D.Alt, A.Alt, R.Alt) What height above and distance from waypoint Bad Berka? Did you have a task active? Were all 6...
I think I had R.Alt, height above aprox. 600-1000 m, distance aprox. 100 Km Only the first two final glide lines where corrupt. I don't remember if I had a...
Hallo all, IŽd like to know what other paraglider pilots are using for polar values: my setup with the following always seems to be rather optimistic about ...
Antoine, Please can you give me your polar and water ballast valuesfor the Duo as well. I will try to re-create on the ground. Were all 6 lines on the final...
Hi, The value's should be: Min speed (mine are 30 km/h and -1,1 m/s) Trim speed (mine are 38 km/h)and -1,25 m/s) Max speed (mine are 55 km/h)and -2,5 m/s My...
Sorry made an error, the trim speed should be 37 and sink -1,2 m/s Edwin. ... Van: Airwaves [mailto:airwaves@...] Verzonden: woensdag 3 augustus 2005...
Antoine, 50% good news. I can reproduce the problem with the data you sent. Thanks. Hopefully I can report 100% good news when I fix it shortly. Paul ... ...
Hello all, I have downloaded and installed version 2.0.0 (25 jun 05). I was prepared for the system reset and databases deletion. I managed to maintain intact...
Hello Marc, First check you have your SUA data loaded. The databases are always there even if empty. Go to the transfer screen and tap the SUA button. How many...
Fix has been found and will be in the next beta version. This problem affected only cases where the target waypoint was the worst terrain conflict. ie: on top...
The easiest way to do this, is to use DocReader on your windoze platform to convert a SUA text file to a palm DOC file. Make sure compression is disabled in...
Or use and SD card if you can. This removes any need to convert the data into a DOC file. Paul ... platform to convert ... disabled in DocReader when ... you...
Hello, This email message is a notification to let you know that a file has been uploaded to the Files area of the soaringpilot group. File : /SP...
soaringpilot@yahoogro...
Aug 5, 2005 9:45 am
4145
Thank you for your replies, When I go to transfer/SUA there is no items in there. therefore I am unable to turn the SUA "on". However as I go into the file...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
