Hi all, The last time that I had my console up and running (about 3 years ago) the left side of the mix was distorted. The right side sounded fine. I tried...
2407
grandchampeen
May 10, 2012 4:12 pm
Ah, I was disappointed in the scan quality, and intended to have it re-done at higher resolution, since some of the schematics are a little hard to read. Then...
2408
grandchampeen
May 10, 2012 4:17 pm
Oops! I need to shrink it more. Look for a lot of smaller files!...
2409
sony-mxp-3k@yahoogrou...
May 10, 2012 5:41 pm
Hello, This email message is a notification to let you know that a file has been uploaded to the Files area of the sony-mxp-3k group. File :...
2410
cadacholland
May 10, 2012 5:45 pm
You can find this information now in the file I just uploaded to the FILES section, called MXP3000Tuchels.pdf Have fun ! Richard...
2411
rborisk
May 10, 2012 6:12 pm
Thank you, Michael. Looking forward to it. A great contribution for our group! Bob p.s., Let me know if I can help by scanning parts of the manual I do...
2412
Michael Crow
grandchampeen
May 12, 2012 2:37 am
I couldn't shrink them enough to post in the files section, so I put them on my band's long-neglected website: www.grandchampeen dot com/MXPmanuals Enjoy!...
2413
rborisk
May 13, 2012 4:00 pm
Thanks! ________________________________ From: Michael Crow <crow@...> To: "sony-mxp-3k@yahoogroups.com" <sony-mxp-3k@yahoogroups.com> Sent:...
2414
randy graves
uvrandalfo
May 18, 2012 5:07 pm
Tom, I finally traced the distortion on my 2mix down, and it was appearing on the output of DLO IC1900 and 2000. I replaced DLO1900 but that didn't change the...
2415
todd_divel
May 21, 2012 1:49 am
Ok, So I just haven't found anything definitive on this. The 212S obviously is for the Sony MXP, the 212L is for the Legacy. It appears they are the same...
2416
Aaron Householter
std1117...
May 21, 2012 2:03 am
Well I've had 8 listed for months. Aaron Householter Recording Services and Supply 1117 State St Salina, KS 67401 785-820-7243 ...
2417
randall3036
May 23, 2012 7:04 pm
its summer up here in b.c. and i just noticed i have an ant problem in my studio !not thousands of them mane a dozen of these little bast***ds in and out of...
2418
randall3036
May 23, 2012 7:04 pm
its summer up here in b.c. and i just noticed i have an ant problem in my studio !not thousands of them mane a dozen of these little bast***ds in and out of...
2419
tniemens
May 26, 2012 9:27 pm
Any movement on the price for the 550S eq's with exchange for Sony para eq's????...
2420
Aaron Householter
std1117...
May 26, 2012 10:24 pm
Well actually I'm trying to buy more 550s eq's with that money. Aaron Householter Recording Services and Supply 1117 State St Salina, KS 67401 785-820-7243 ...
2421
tniemens
May 28, 2012 4:07 pm
With what money??? I thought you were trying sell 550s eq's?...
2422
Aaron Householter
std1117...
May 28, 2012 4:39 pm
Ah that was the old days ;-) buying 4 more Now to load out my console to 48 Aaron Householter Recording Services and Supply 1117 State St Salina, KS 67401 ...
2423
gnrom
May 31, 2012 11:43 pm
Hello Everyone, I was wondering if there was a field packet out there with information on doing this conversion. I have been thinking about it for a little...
2424
Douglas Ferguson
the_d_u_g
May 31, 2012 11:58 pm
Your console will sound better!! I did the conversion and was amazed at the difference. I bought faders though.. Good luck Oh and you'll be able to get a good...
2425
Tom Graefe
consoledewd
Jun 1, 2012 2:08 am
Just look at the Non Automated Fader schematic and take the heat shrink off of one wire on the Fader harness at the Lower motherboard and insert it. Later Tom ...
2426
gnrom
Jun 1, 2012 11:41 pm
Thanks, That's what I've been told. Did you just use the former automation fader faceplates, or make new faceplates? If so, does the dB legending line up...
2427
Douglas Ferguson
the_d_u_g
Jun 1, 2012 11:52 pm
I got the manual fader packs it was just plug and play. You'll have to make some new circuit boards at the very least.. I'm guessing you could try to use the...
2428
Tom Graefe
consoledewd
Jun 2, 2012 12:54 am
The legend should line up, almost, if you use the loading resistor on the Non Automated Fader schematic. Tom graefe@... http://GraefeDesigns.com/...
2429
gnrom
Jun 2, 2012 1:04 am
By "fader packs" do you mean the complete fader module from Sony, or just the faders. What circuit boards would I need to make. Tom suggested something...
2430
Tom Graefe
consoledewd
Jun 2, 2012 1:14 am
No way you can get manual Fader packs. I believe I sold about the last ones in the world to Doug. You would have to ditch the Faders and PCB of the Auto...
2431
ndruce
Jun 2, 2012 12:53 pm
Hello, I am installing a 3036 in a friends studio this weekend and the one problem I have not fixed is: in ch slots 29 and 30 I only get audio to the 2-mix if...
2432
randy graves
uvrandalfo
Jun 2, 2012 1:31 pm
Norm, I have quite a few manual fader packs, as I bought a console for parts recently. I don't want to sell them all, but I could sell you 16 if you want to...
2433
Douglas Ferguson
the_d_u_g
Jun 2, 2012 1:49 pm
Awesome. That's like waxing 1/2 your car. Put them in and you'd have a fully manual console in no time. Plus you'd have a working prototype to base your others...
2434
randy graves
uvrandalfo
Jun 2, 2012 1:56 pm
And if you wax the driver's half of the car first, you get to look at an apparently fully waxed car at least as you get in! Randy On 2Jun , 2012, at 7:49 AM,...
