Hello Everyone. I just joined the forum after buying a MXP-3036 for my new studio in Philadelphia. Just wanted to know if anyone could point me in the...
Howdy everyone. For those of you who need a VF frame or want one for some parts I've got 2 for sale. One is the frame w/leg, meter bridge w/ps. Second is frame...
Hello Jeff, I need a little help with the jl Cooper... I have tried with various setups and I can ´t get to run the automation. -mac classic II, mac classic,...
... It's been a LONG time since I've had mine hooked up (my console was in storage for 6 or 7 years, and I've only recently installed it in a studio) so I'm...
Hello, my memory is vague on this but, seems to me you have to select an option in the Mac itself, within a hardware setup page. I'll have to get on my System...
Richard, Good to hear you are alive and well. Tom Graefe ... Hello, my memory is vague on this but, seems to me you have to select an option in the Mac itself,...
I"ve got 32 VCA fader packs for sale Call me.. 512-293-7279 Douglas From: sony-mxp-3k@yahoogroups.com [mailto:sony-mxp-3k@yahoogroups.com] On Behalf Of...
Hi, I saw your message concerning the MS-3000 automation. One (often overlooked) question: You DID connect the highspeed data cable and the RS232 cable...
Reading my mail to you again it slipped into my mind that dipswitch number 3 at the back of the MS-3000 unit did get a function later on: The switch could be...
My JL Cooper autamation is working now, I had to remake the de 9 dsub to mac serial conector following the pinout that you sent me. It´s seem a wiring...
I have a MXP with JL Cooper automation that has never worked for me. when I turn on the auto power supply, the faders look like they do a self test then lock...
It sounds like you don't have the automation power supply. Douglas From: sony-mxp-3k@yahoogroups.com [mailto:sony-mxp-3k@yahoogroups.com] On Behalf Of dhhaudio...
Nope, I wish it was that easy. I have the Sony MXP3000 Automation power supply and it is putting out + - 18v and +8v the faders go through test ok, they just...
Check your 5 V automation supply at the Motherboard in the console. It should be over 7 volts at the Motherboard. Check it at both ends of the automation...
Yeah, it sounds like your host computer is having troubles. I've had similar symptoms when the CMB board went "funny". Also check the fader bus terminator...
here are the voltages, 6.08v across the board also I was wrong about the fader readouts, the channels say L and the master says A also, nothing I do changes...
DAVE, 6.08 Volts is barely enough considering the Voltage regulator, low drop out , requires 0.75 volts. L on the Automation faders and A on the Master is...
Does anyone have the dip switch assignment settings for wild faders for MXP 3036 I have AFB II faders.Also looking for a group of 8 VU meters I can supply a...
Does anyone have the dip switch assignment settings for wild faders for MXP 3036 I have AFB II faders.Also looking for a group of 8 VU meters I can supply a...
The dip switch settings are in the operation and maintenance manual book. It's on page 2-14 table 2-6. I have a 36 ch. console so my first wild fader is ch.37...
Thank you so much David! That's very helpful info. My manual only shows the settings for the first 36 channels so I'm grateful for the time you spent typing...
Jeff, Glad to be helpful. Sorry for the two typos. My console is doing good. I ended up buying 5 transformer ch. from Alan a while back. I have a few muddy/...
Hello Everyone, I hope this isn't too far off topic, but i recently got a Sony MXP-2000 and am hoping there are some similarities in parts with the 3000. I...
glenn, Not one single thing similar between the MXP3000 and the MXP2000. The connectors are like those used on Video cameras. I hope that helps. Tom ...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
