Hello everyone. I run The Seaside Lounge, a two room studio in Brooklyn, NY. We have a 3036 in the A room and a 3020 in the B room. Check out the studio at...
HI, I have recently acquired an ex Japanese OB van that has a Sony MXP 5000 installed in it. I am trying to find out any info on this console. Do any of you...
I was around when it was designed. Tom graefe@... ... From: Richard Baker To: sony-mxp-3k@yahoogroups.com Sent: Thursday, September 20, 2007 6:41 PM ...
Hello I have for selling or interchange 36 non VCA fader modules , MXBK-MI31 Pre amps and MXBK-EQ31 Eqs modules. I need the pinout for Eq modules.I have the...
Hi guys, I know that we Sony board owners have a wonderful built in patch bay, but just thought I'd let you know that I have a really nice one for sale. You...
Hey guys. I have a couple of frames for sale. One is a VU frame- frames, legs, meter bridge. No PS at all. The other is a frame w/o legs- frame body, meter...
I buy a pack of audio mixers and audio perihealps of Broadcast Tv Channel,and this pack have all modules of 2 mxp 3036 consoles. I will be racking some Eqs...
Hey guys, noobie here. I understand that there are five EQ modules for the MXP: MXBK-EQ31 = standard MXBK-EQ32 = switchable Q MXBK-EQ33 = Full parametric ...
Has anyone used/own/have any info about the tube channel strips Fred Forssell designed for mxp3k's? I heard they had a compressor section along with the eq,...
I have a few questions, The first one is I want to recap my console, How or what do I do to test the new caps for bad ones or duds before installing them. The...
Dave, Why are you focusing on capacitors? Do you have any loss of level at very low frequencies? If not leave the caps alone. Most will last a lifetime....
Thanks for the reply Tom, Sorry, I thought that the caps would be most of the problem. Some of my eq's lost all the bass and the highs feedback on others eq's...
Yeah the 100 UF caps have been known to go bad in the EQ's. I now know of two consoles with that problem out of 450. The Mono meter bothers me. Have you...
100uf? Are those in the stock parametric EQ's? I was talking about the verible Q EQ's. What Caps would that be? And will that cure the high frequency feedback...
Hi, I'm a new member with a problem. I teach at a small university that inherited an MXP-3000. After being stored in a garage for 4 years, I was thrilled that...
The stock EQ was not the parametric it was the wein Bridge EQ 31. If you are getting Oscillation on the Parametric EQ's, I have heard of this a lot and I...
Did some test last night. One channel runnig a 0 signal centered is -10 on the master L/R vu and mono meters, When one channel is running a 0 signal panned...
Dave, When you put 0VU, +4 dbU, into a tape return and pan a channel left or right, with the master fader wide open and the channel fader ar Unity the left or...
Tom, The good news is that all the levels are what you say they should be. The bad news is I can't figure out why this thing is distorting at a low volume....
Is this an automated console with VCA's? If so the +/- 18 volts rails may not be matched and the IM distortion of the VCA's may have to be adjusted. They have...
Check your voltage rails +/-18V. I thought you were getting distortion at low levels only not that the distortion started at low levels. If the rails are low...
Tom, Yes, This is an automated comsole, and yes, the distortion starts at low levels and gets worse as the faders go up. Sorry if I didn't explain it enough to...
The automation supply has nothing to do with the +/-18V UNLESS the auto supply and the console power supply are not plugged into the same outlet. The third pin...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
