"stéphane poiraud" <steph.azu-@...> wrote: original article:http://www.egroups.com/group/st6-list/?start=17 ... I think perhaps I had the same problem...
20
Luis A. López
selica@...
Apr 26, 2000 6:09 am
"stéphane poiraud" steph.azu-@... wrote: original article:http://www.egroups.com/group/st6-list/?start=17 ... board w/ a new ... do all of this ... ...
21
Petr Mikse
petr@...
May 30, 2000 3:36 am
I have a trouble with some my SW: Although it works OK on ST62T65B, it fail on ST62T65C. I have discovered some diferences between C and B version of MCU, but...
22
Jose Moreno
a900302@...
Jun 1, 2000 1:33 am
Hello, I have to make a digital dice with 7 LEDS, 1 start switch and 1 stop switch. I made this program but, being my first one, I don't know whether it will ...
23
Luis Lopez
selica@...
Jun 15, 2000 1:54 am
Petr Mikse: that SW means?. 1. - does this happen when you program the port C like SPI?. If it is correct you don't generate pulses by this port. You should...
24
Petr Mikse
petr@...
Jun 28, 2000 1:07 pm
Luis Lopez: Thank you for your answer. That SW stands for software (program) for ST62T65. I didn't know that isn't common used abbreviation. Sorry. 1. Pin...
25
martin.milnes@...
Aug 14, 2000 4:20 pm
Is anyone programming ST62T60C (repeat C) parts using the Windows Epromer 3.3.0.0 and the ST626X Starter Kit? I am having problems. I can program ST62T60B. ...
26
Luis ALópez
selica@...
Aug 16, 2000 3:12 am
I need exactly now what is your problem, if not have comunication maybe is your programing board, look with osciloscope the signal when you program ST62T60C...
27
Luis A. Lopez
selica@...
Aug 18, 2000 7:30 am
Hola Martin I build my programing board, use epromer 3.3.0.0, try the Msdos programming software this is in directory st62xli , if not a first time somebody...
28
Petr Mikse
petr@...
Aug 19, 2000 11:23 am
Try break the connection between HC125 (LS125) and the OSCOUT pin of ST62T60C on your programming board. It works on ST62T65C OK, though I think it will help...
29
hacketta@...
Aug 21, 2000 11:04 am
Started some resources pages on my site. Early days yet but with YOUR help we can improve on what is there! Have a look at http://jenal.com/st6 and send me...
30
Bryan Whitehouse
bwhitehouse@...
Aug 21, 2000 3:12 pm
Hi all, Are there any ST7 user on this list? Would it be worth creating a similar mailing list for this device. Thanks Bryan...
31
martin.milnes@...
Aug 23, 2000 8:24 am
Just a note to let you know that our problem has been solved. We replaced the 74HC125 on the ST626X STARTER KIT with a 74LS125 and now we can program ST62T60C...
32
Alan Hackett
hacketta@...
Aug 23, 2000 9:38 am
Martin: Glad to hear you got the starter kit working by changing the HC125 for a LS125. This seems to be the answer for those having problems with the "C"...
33
sunilv@...
Feb 13, 2001 10:44 am
From Sunil, First time user for ST6 series. Used ST62E20 to design a battery charger. To monitor the status I connected charge LED and done LED to PA1 and PA3...
34
Henry A. Vermeulen
inderdaad@...
Feb 17, 2001 3:33 pm
Sunil, From what you discribed the ST62E20 shoud not fail, so something else must be the problem. Remember that the TOTAL current through port A and B together...
35
Luis Lopez
selica@...
Feb 19, 2001 2:26 am
Helo Sunil reading your email the power supply is more than 6 volt, because if you answer is yes you blow PA1, PA3, you needed look the manual about this ...
36
Sunil Vadgama
sunilv@...
Feb 19, 2001 8:50 am
Dear Luis, Thank you for your reply. I found out what is wrong, it is my program. I used Realiser version 2.01. With lot of experiments I found there is a...
37
Sunil Vadgama
sunilv@...
Feb 19, 2001 8:52 am
Dear Henry, Thank you for your reply. I found out what is wrong, it is my program. I used Realiser version 2.01. With lot of experiments I found there is a...
38
Grzegorz Zajac
gzajac@...
Feb 19, 2001 7:39 pm
... Najlepszy system zarabiania w Internecie: http://zarabiasz.pl Najskuteczniejsza forma reklamy w Internecie: http://reklama.zarabiasz.pl...
39
Mike Shegog
mshegog@...
May 16, 2001 2:38 am
I have a programmer which came in my evaluation kit. st62e1x "Basic Programmer" have been using it with the 4KB st62e25 devices for ages. Now eed more program...
40
j.kasielke@...
Aug 28, 2001 9:36 am
Hello, witch are the Pins to program the ST62 T 00 or 01 ? I found all members of St62-family to programm it in-circuit but not these. Thanks Joachim Kasielke ...
41
Petr Mikse
petr@...
Aug 30, 2001 10:57 am
Hi Joachim! AFAIK, the ST62T00 (01) is in principle the ST62T25 in smaller package. So corresponding pins should be used to program it...
42
alaurico@...
Oct 14, 2001 5:01 pm
Hi, I´ve a programmer for ST6225, and I'd like to use it with ST620X devices, so I´ve tried that information, but it seems not work. May be I´m doing...
43
Mike Shegog
mshegog@...
Oct 15, 2001 2:16 am
Hi Alaurico. exactly which programmer do you have ? and which software to run it ? - Mike Shegog ... -- /v\ î |< é...
Hi Mike, First of all thanks for replying. I`m using a programmer published in "Elektor". It´s the same as in http://www.eprat.com/DOCS/st6prog.htm and the...
45
Mike Shegog
mshegog@...
Oct 16, 2001 10:47 pm
Hi Alaurico, glad to reply, I've been struggling with st62 devices for years, there's not been much help from ST. I'm wondering if we have the same dos...
Alaurico Please be aware that some of the newer chips have a different programming algorithm than older versions of the same. For instance I use the ST6265. I...
Dear Guys, I am looking for information on programmers. Would like to make one so if any one have a schematic I would apprieciate it, if you have the PCB...
