... Why not post a few detailed pictures of it to the FILE section of this mailing list? The photos section will be useless as pictures are not shown in full...
... Joels site is now a static repository of information. Joel died recently so there will be no more repairs and any new repairs implementing his solutions...
... The best source I found is that shop on eBay. I am not in the mood to shop there yet. I need to have hinges too with a new lid, and so far they have not...
... There exist an infrared remote for it so I do not believe it is older than 1980 at the most. Looking at the pictures (of the original Technics remote on...
Hi Folks, I own a Technics Turntable SL-D30 an automatic direct drive turntable and I need a replacement for the platter rubber mat (spare part #SFTG Q34 NO1)...
... Get a mat from another table in at least the right size, then trim to make it not hang out over the plate on your deck. Make holes in the mat to suit the...
Hi Amy, Try this website, www.partmaster.co.uk It is a shop in the UK, They stock a lot of Technics spare parts and I saw that they have the stylus for SL-D30....
Hi Mikkel, You are a genius...Wow! I have tried some of the suggestions you mentioned but I wasn't really accurate. The tone arm is still bumping up and down...
... I just ran a search for that number on www.ued.net and I came up empty. I still think making the deck into a manual deck is the best solution until you can...
2031
technics@yahoogroups....
Nov 29, 2008 2:22 am
Enter your vote today! A new poll has been created for the technics group: I propose to elect a moderator to handle maintenance of the group. o Vote to get...
2034
technics@yahoogroups....
Dec 8, 2008 2:42 am
The following technics poll is now closed. Here are the final results: POLL QUESTION: I propose to elect a moderator to handle maintenance of the group. ...
http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&item=110323744680 I am not the seller but I wish it was possible to disassemble and send to me as I really want...
Does anyone know if an SP10 MK II will fit in a MK3 SH-10B5 obsidian base? I'd hate to buy a MK3 base and have to wait for a MK3 SP10 to come around, they seem...
2038
technics@yahoogroups....
Dec 28, 2008 4:26 pm
Hello, This email message is a notification to let you know that a file has been uploaded to the Files area of the technics group. File :...
... disclosing the offer ... Thanks for the reply, Mikkel. I went to look back at the ebay ad (item 160305806877) and the seller had "pulled" it. I've been...
The SH-10B5 base has reappeared, same vendor, ebay UK item 160308564773. To recap, it has a round cut out that only the MK3 SP10 will fit, not the MKII SP10. ...
Interesting Q&A before it was pulled (may reappear too): Q: any idea if it could be cut out to fit a mk 2 sp10.thanks. 11-Jan-09 A: Hi,yes it can be cut out...
Just a quick heads up! Someone wants to sell a deck and a plinth. http://www.vinylengine.com/phpBB2/viewtopic.php?t=16529 You have to be registered to post...
For when you want to buy second hand audio equipment.... ....but do not want to end up at eBay. Sites for sellers and buyers that may also have other forums,...
Hello, The speed on my SL-BD1 has started to vary up and down. If I try to adjust the pitch at a certain speed, the speed either doesn't change at all or...
Your deck is belt driven so the belt stretches with time,not quartz locked...we used to take it off and put it in the fridge(but I cannot say for a fact it is...
Thanks for your reply. Actually, the belt has just been replaced so I am sure that is not the cause of the speed variation. Is there a way that I can check...
... There is more than a speed pot to the story. When the speed is not locked to a quartz crystal, there is still a circuit that has to work. And when the...
