Hi, My name is Luc Lachance. I am presently developing a digital camera using the tri-media PNX-1302EH. Few months ago, I had an issue with the Intel PCI...
I don't have the complete answer for your question but here the concept: 1. The WLAN must interrupt the PNX. You have to install a PCI interrup handler. 2....
Luc, If the pin cannot be driven to the low level but only to 2.5V, it could be a conflict on that pin/pcb track. All the PNX13xx PCI PADs are the same so your...
Hi Luis, I have removed the pull-ups on the PCI address bus. The issue is still there except that the faulty signals are now low most of the time. When they...
I recently upgraded from NDK 4.3 and TCS 4.51 to NDK 5.4 and TCS 4.61 and have since been experiencing the following weird problems (one minor and one severe)....
Unless it is in fact an instance of a speculative load crashing the PC, the severe problem does not directly map to anything I have ever heard of before. It...
Hi, all I'm planning to develop on the STB810, but I'm confused. I need your help. As you know, the PNX8550 in the board consists of two TM3260 and one MIPS32....
STB810 uses TriMedia TSSA components but in a way that will be very new to established TSSA users. It also uses Linux and WinCE so a user needs to know about...
A long shot idea. If you are using MDS' LCP, try switching to the standalone EEPROM and reset the board. Then use another computer with JTAG and dvpMon to...
I don't see a reason to bring in JTAG to the PCI environment. Both the TD and DP buffers (address in the BIS) are designed to survive a warm reset. Reset the...
I tried setting the [HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\\PNX1500\Parameters] "SpeculativeLoadFix"=dword:00000001 per page 13 (a.k.a. 1-9) in ...
I am playing around with my PNX1500 tmlAo demo. However I am getting no sound from any of the output audio jacks. I realize that there may not be a valid...
What hardware are you using? Best Regards, Alfred Lee ... From: "wenhua82" <boonwah@...> To: <trimedia@yahoogroups.com> Sent: Wednesday, September 06,...
Alfred pointed out the "windows won't boot without a power cycle" part of the post. Then yes, JTAG might be a way to get it. Sounds complicated. As to the...
Run ${TCS}\tmComm\bin\tmregistry.exe. It tells you what registry keys are in use. When you get speculativeLoadFix in the right place, that utility will tell...
To bring the group back to the real priorities, does anyone have any idea how to get the NXP Powerball to work? I can get mine past the start-up phase but it...
Thank-you once again for your assistance, I should never make assumptions, just because it didn't crash in 4.3 didn't mean it wasn't a problem in my code. I...
Assuming that this is what you are referring to you need to feel like you are fighting the inertia, if you don't get that straining feeling and keep in sync...
... Alfred, I guess you need to be on the NXP VIP guest list to qualify for the Powerball. What message do you think it is meant to convey? Maybe that it you...
I can't retrieve anything from the buffers because the machine reboots immediately upon trying to run the application. Even if they could survive a warm...
I thought my Momentum with Philips will carry over, no? Any way, I have one of those gismo. Best way is to show you face to face. Next best is 720p video...
Hi Luc, Nope, I have never seen something like that and I quite do not know what to think about it other than there is something basic that is wrong: - Is...
Hi, I am using a system that is provided by Phillips. Not too sure about the hardware I am using. But it comes with a USB port, 9 component in/out jack, a...
Please describe the system more. Box size? What does it say on the outside? I can't yet identify it from what you have said. Chuck Peplinski TriMedian at...
Hi, The thing is that this board was given to me by Philips. It comes with 1 USB, 9 component output jacks, 1 serial port and the JTag set. There is a 30Gb...
All of the info you need can be obtained at www.tcshelp.com. Log in and create an account. When your licenses are verified, all of the necessary info is...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
