... There isn't any "correct" configuration. You decide what you want built in, like compiling a kernel. However, I suspect that it won't help you. The "sh"...
... Right.... I'm getting hauled into writing kernel modules, kicking and screaming all the way... So, I'm going to have to write a kernel module that enables...
If you look in the Technologic Yahoo group, I've posted an example driver that does just that. Sorry but I don't have web access right now, so I don't have a...
... Andy: I'm trying to decipher your example code.... Unfortunately, being a newbie in the world of IRQs, I am having a bit of a hard time.... --Yan...
... Andy: Here's what I am trying to do (at least for now): 1. pick a GPIO pin 2. set it up so that an interrupt is raised on both leading and trailing edge ...
You'll absolutely need the Cirrus Logic Data Sheets for this. Although there may be a link on some of the technologic stuff, you should probably just google...
Does anyone have any experience with the new TS-7260 SBC? Jesse, Eddie; Do either of you have more information than is one the web? The development kit does...
... Well, because the IR sensor I need runs off of 5V; if I can get 5V TTL then it's just a matter of hooking it up... Otherwise, I will need more components...
... resistor? ... Yan, It looks like the Vishay part is a remote control receiver/ demodulator. All you need to do to "condition" the signal is to use a ...
... Fine run the power line from the 5V line. ... Yes. As I said just use a couple of resistors or a resistor and zener to limit the output to 3.3v and feed to...
hi all first question is i have a 256mb CF card , its now formated as ext2 and mounts ok but have a problem , using a laptop with knoppix and the debian tar ...
Dave -- Maybe you can try to shrink the NFTS partition in order to make some room to create a swap partition. Knoppix 4.02 has 'ntfsresize' that can do this: ...
I've been working with the prototypes the last couple months. Nobody has any of these boards yet except for a few very special customers. Our production run...
Dear all, I am tring to connect to my ts7200 board through Telnet. However, when I try to login it asks for a password. what is this password? And how I can...
dont realy want to do that , theres too much important stuff on the drive i have plans to upgrade it to a bigger drive and dual boot ,but will be a couple of...
Hello, I am new to TS7250, I have an issue in using PHP. The user manual says that "Apache with PHP" installed. I edited a small PHP file, hello.php and put it...
... WOW! I want one! Seriously, if I read this correctly, this should make implementing things like LIRC fairly easy. LIRC (Linux Infra Red Receiver -...
... Just a guess, since I've never done any PHP, but do you have execute permissions set correctly on the file? Mike ... Mike Dodd - Montpelier, VA ...
Jesse, Eddie, I'm interested in using the 7260 in a battery powered environment that is recharged by a large solar power array. The system, like many others...
... Have you just pressed <ENTER> at the passowrd prompt, that is given it a NULL password? Some telnet daemons are funny about allowing remote root access. ...
Thanx Jim. I tied the ssh 192.168.0.50 And it works with my root password :-) _____ From: ts-7000@yahoogroups.com [mailto:ts-7000@yahoogroups.com] On Behalf Of...
Since the manual says PHP is enabled, I am very interested in using it. I tried to use 192.168.0.50/cgi-bin/hello.php to access the hello.php file. However, I...
I am trying to get the Analog TS9700 Board to interface with my TS7250 Arm board but have hit a wall. Here is the code I tried using to access the Analog...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
