Hi All, Im having a small problem with an external estop, I have converted the control on an old denford orac and have wired the existing estop switch normally...
It may be prudent to keep the copy on the Dakeng site up to date. You are distributing known buggy software. At least it should say "always check for the...
How can I set the current position in TurboCNC, so that I can home, or jog the cutter away and change the tool, and then have TurboCNC move the cutter back to...
MY method is to do it in my g-code. I have a previously selected point that has the clearance to do the tool change, raise the quill to the top, turn off the...
I have got a cut file loaded using "Run From File". Now I go to Jog and use things like the "G", "Z", and "H" commands. Next I go to "Run /Single Cycle" and...
I have got a cut file loaded using "Run From File". Now I go to Jog and use things like the "G", "Z", and "H" commands. Next I go to "Run /Single Cycle" and...
... document. ... faster ... the patch ... TurboCNC 4.0 and ... Thanks Jerry it works now. It means however that the programmers guide is not correct. Om page...
Hi All, When running a program in Tcnc the limit switches are tripped when Im nowhere near them. This happens randomly and not all the time. Could this be an...
Dave: An easy method to do this is to reserve a 'Fixture' or alternate set of coordinates for this purpose. For example, let's use G59 as our 'Tool Change'...
Can I save jog points to the floppy instead of the c:\turbocnc\points file? If so where do I change this? Thanks As it is now I have to jog and save then exit...
OOPS my bad..Wrong Forum.. I do have a question for Turbo cnc users (v 10) though. I draw a 6" square box and save it as a dxf file. Then I open it with ace...
Explode it before you save as a .dxf Gerry ... fillet tool and save it. ... zippo. ... talk to me! ... question too? ... c:\turbocnc\points file? ... then get...
Hey Gerry........ YOU DA MAN!!!! Thanks for the fast response! "It worked" And now I got to go get Sweetie some flowers! :-) ... From: notoneleft To:...
... Config->General Under point cloud file - specify complete file name, eg a:\points.dat; To your next post - Yes, this is the right place to ask your...
Hi, Troy: I assume that you're running Rel-4. On the top menu, select the item labeled "Configure." TurboCNC will respond by showing the configuration menu....
No I am running 3.1a. Is there a way to do it in there? ... From: Carol & Jerry Jankura To: turbocnc@yahoogroups.com Sent: Tuesday, November 02, 2004 7:12 PM ...
Gentlemen, I have read with interest the posts on the Dos drivers for USB "memory devices" I need to buy 12 motherboards for machines I plan to build next...
I'm new to all of this and wondering if anyone that is using one of these controllers would be willing to share their INI file. I think I have it set up...
Ray where are you located? ... From: ray_jorgensen To: turbocnc@yahoogroups.com Sent: Wednesday, November 03, 2004 12:09 PM Subject: [turbocnc] INI file for...
I have 4 steppers 4 my foam cutting machine. I use the L297/L298 combination to control them. The motors are 9 Volt 1.2 A/Phase. The mode that I use controls...
I have just upgraded to turbocnc v4.0 When I tried to open a few .txt files, it gave me the message "file error: unable to reset the file" What am i doing...
The option I chose was to use a compact flash to IDE adapter with a 32 meg compact flash card. This aproach will work with any motherboard that supports IDE...
... I looked through the source code to find where this error occurs. It occurs when you've chosen to run a program from the disk (and not load it into the ...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
