I have sent some e-mails to Dave Kowalczyk (from September the 9th...) but I didn't receive any answer. I have used both the e-mail address admin@......
HI (name?) Why not just provide Dave with translations of the manual and software and post them on THIS website. Remember, Dave's work is financed by the ...
... Even when Tony and I were collaborating with Dave on getting TurboCNC 4.x out the door, this would be Dave's decision alone. Now that neither of us are ...
Dear friends I want to desing a new three axis cnc with stepper motors which will be an open loop system for educational purpose. I want to make motor drivers...
Cengiz, One of the big advantages to using TurboCnc is that it is fully customizable! Having said that, the usual practice that I have seen and use myself it...
Hi Cengiz, As Art said the printer port is fully re-configurable. For stepper drivers there are lots of designs around but you ought do decide just how good a...
... be an ... myself. Do ... stepping ... motor. ... I have a WORD document that has the port and lines so you can write in what you used each pin for. I keep...
... turboCNC ... TurboCNC 4.x out ... us are ... primarily to ... The last ... and doing his ... when the next ... those of you who ... interpreter ... ...
... Dave, I think you would be well served to post some 'statius' and then if it is that you are locking himself in our lab, fine, if you are taking som e time...
Cengiz, There are lots of schematics floating around on the web, google is your friend. http://www.dancad3d.com/ has details of a discrete component bi-level...
Hi, Dave M, others: Anyone who's coded a "specialized" version of TurboCNC is encouraged to post the executable to the files area of this list. Since the...
Folks: Sure thing. I've seen "Dave K" around a bit, so I'll tell you what's going on with him... :) Fact is, I just have been spreading myself too thin...
Newbie question somebody can hekp me with ? On my TCNC startup screen is the message: "Pentium timing not available in protected mode" I'm running DOS 5.0 with...
From: "skerbitz" <skerbitz@...> ... From every thing I've gotten reading the docs and reading the code, you can't use the Pentium timing functions if you...
I'm back to tcnc after about 1 year break. Did some rewiring, configured home switches and limits active high. They work fine on a port monitor, but don't...
Alex, Just guessing, but if you have "HomeasLimits" set, you do NOT set up limit switches in the config. Bubba ... Bubba OLDER THAN DIRT Country Bubba ...
... If I recall, there's a problem with early Pentium computers not being able to execute the real time clock instruction when the Pentium was run in protected...
... Hi, Alex: How are you getting your "active high" signal? I'm assuming that your computer always indicates a limit condition, right? If that's the case, you...
hi- we've written up a how-to that actually will be updated later tonight to include a more accurate diagram (since we came to a half-correct conclusion that...
Art, I don't remember setting homes as limits and I even don't know how to do it. Where do I look for it? Alex ... [Non-text portions of this message have been...
Alex, It is under: Configure General Configure Left column about 5 lines down. (Check box) Art Also, when setting up home switches etc, I suggest doing it one...
Ok, just looked - that box was not checked. May be my problem has to do with the negative/positive business? Alex ... [Non-text portions of this message have...
Jerry, I actually have signal going through the resistor - 10 K.In my case it goes like this: Ground-10K-pin-NO of the switch-5V. This is why in my case I get...
When I switch off Geckos, what do I turn off first - motor power or 5V? Btw, the motion is extremely smooth - I tried several drives before - no comparison,...
Alex, I have always seen it wired something like this (hope the ascii art works) +5V ... Res Pin_____| ... Switch ... GND If you have a NO switch, it will be...
Hi, As Alex has it wired, using a 10k as a pulldown, could be and issue. 10k is a large value for a pulldown and the current will be very small. Leakages into...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
