Roland, Thanks for your input. I have taken what you said and added a brief porfolio of my self and my work. I am an avid furniture builder and have posted...
Thank you for you input. I have taken the time to input a profile (under member name dreedy) for some of the work that I have done in the past year or so (I...
I have to agree. I use www.jobshops.com for finding people who are in business. it is pretty easy to send out drawings and get bids. I think a few requests...
I need help to porting the turbocnc setup for my 3 axis into mach3 program, who can help me? If it needs I can post my turbocnc.ini file... Gianluca...
Here is where you can watch all the instruction videos on Mach3. I think the first or second one is on setting up all your pins and directions, Then watch the...
Rick: They are. Average is about one or two a week these days. If you sent out reg info and didn't get anything back as a reply, email me offline. dkowalcz...
Great, thanks for info. ... ____________________________________________________________________________________ Be a better friend, newshound, and know-it-all...
Hello, PLease, could someone tell me if he uses Tcnc and an HP Pavillion 7865. How to use this PC in real DOS mode with an Windows Miellenium? Maybe this...
Danielgouze@...
Jan 7, 2008 6:04 pm
18881
Hello All I'm having problems with my initial setup of my Taig Mill. I have followed the instructions in the manual and can't seem to get it right. Is there...
The limit switches are making me crazy on me with turbocnc they dont work all set active high or active low. The y comes out inverted somehow in the port setup...
The limit switches are getting weird on me with turbocnc they dont work all set active high or active low. The y comes out inverted somehow in the port setup...
Hi Turn on the port display, and press each limit switch. You should see the colour toggle. Make sure you have three different lines toggling. Write down their...
Roland, I set and checked the limits with the following results: limit x pin 10 shows brown, toggles to green limit y pin 11 shows green, toggles to brown ...
Ed, Pin 11 is inverted. Set that one to active high and I think it will work. Pin 11 is inverted on the parallel port! As a reminder, don't forget to reset...
I use pminmo electronics, switches are normally closed The inputs are pulled up to 5V and the switch is from the pullup to gnd. Since all the software out...
If you press F1 to get to help, then select index, and type in MS you will get a list of help topics for MS-DOS. Select MS-DOS Prompt and it will suggest...
everyone, I have been away for a while, I just downloaded Ace Converter 3.2 I used the older version before and Im having problems. Is there a way to force...
Funny, I am attempting to use Ace right now to cut a lathe hand wheel dial... lots of short, medium, along lines and a few numbers. I did the drawing with...
Thank you, for your answer. Yesterday evening I tried a Real Dos patch for windows Me found on internet under a place :"geocities". I failed. Tonight the PC...
Danielgouze@...
Jan 8, 2008 8:50 pm
18892
I use to be able to force it to start at 0,0 and it would output g-code from 0,0 and go till all connected lines were done. EZ not now!...
I have been playing with this and I figured out a couple of things. But, I would rather just go back to the older version. anyone know where I can get it. ...
And you system will run faster with Windows 98SE than with ME. 98SE is one of the most stable versions of all of Windows. Do search Microsoft.com for the final...
I just upgraded from TCNC 3.25 to 4.1. My machine ran just fine in 3.25. I used my 3.25 .ini file to start the new setup. I went thru the 4.1 menus and added...
Chris, I believe this is a known bug in 4.01 (Homing issue). As for the jogging issue, I don't have a clue as it works for me. Bubba ... Thought for Today: ...
Hello I am having trouble setting up Turbo. I have my axis configured and everything jogs well and it runs the g-code. My problem is that I am not sure how...
Bubba, Do any of the versions in the files section address these issues? I see one that you fixed and compiled in order to implement G28 and homing. There's...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
