can someone give me some indications on the workings of turbocnc versus this interface..If i am wright it uses some pins of a parallel port for output..Since i...
Does anyone happen to have a working version where the backlash compensation speed is NOT set to max speed but to a lower speed? the reason I am asking is...
with the post mpltcnc.pst if i generate threads with mastercam using long hand method the program generates G33 Z-1. F.05 how do i edit the post to get K.05...
I just tried posting a longhand G33 thread and it worked fine.I'll overwrite the post in the files section if it will let me. If not I'll put another...
Hello, This email message is a notification to let you know that a file has been uploaded to the Files area of the turbocnc group. File :...
turbocnc@yahoogroups....
May 4, 2008 7:36 pm
19160
it's been way to long since I've edited a post for mastercam. A quick way to do it is t open the file in word and use the find / replace option. Not as good as...
Hi folks. I see G2 going quite slow, considerably slower than the feedrate if arc is 90deg and small size. (a program that uses many runs for ages !!!!) Any...
... worked fine.I'll overwrite the post in the files section if it will let me. If not I'll put another mpltcnc.pst in the files section. Sorry for the trouble...
I think it was dumb luck that I got the post proccessor to work at all.I'll try to alter the canned cycle section when I get some time.I know nothing about C...
Hello, This email message is a notification to let you know that a file has been uploaded to the Files area of the turbocnc group. File :...
turbocnc@yahoogroups....
May 8, 2008 1:40 am
19165
I have uploaded another .pst file. This post seems to work for longhand and canned cycles, with exception of tapered threads.I believe turbocnc doesn't...
Anybody have suggestions for sourcing inexpensive power caps for power supplies? I need something in the range of 25k - 30kUF, 75VDC. Thanks, Andrey Lipavsky ...
... Hi, Andrew: You might want to take a short drive up I-75 to Dayton and try Mendelson's They're in the downtown area, near the stadium. Also, there's a...
Hi Jerry, Of course, Mendy's! Thank you for reminding me. That's a great place. I'll have to checkout Midwest Surplus as well. Thanks, Andrey Lipavsky Essex...
Hi all, I've come back to turbocnc after 2 or 3 years with no cnc toys... previously I used it to drive my lathe, and now I've converted an old sherline mill. ...
I was using TurboCNC on a lathe and was having problems with the interface. I connected direct via the parallel cable. As advised by Gecko drive, I installed...
... SOUNDS - like step and direction signals are reversed. Try swapping the settings for those on an axis and see if that makes a difference. -- Lester Caine -...
Lester & Roland; Thanks for the tips. I checked all the connections and voltage levels with a meter. Wires are connected correctly and levels change as I jog...
in order to get the piecework function to work I have to open the file in editor, and run it form there. Does this sound right? Shouldn't I be able to run from...
Hi ppl, I know this is thread is ages old, but i was searching for "homing" and it came up. One posible reason to have the system behave as in the original...
Hi all, I am new to this board and to CNC everything...So, i say HELLO to tcnc community! My machine (for now) is a 10x18 Craftex lathe, i have a hobbycnc ...
Hein You might want to check under the Configure Axis submenu. In there under Scale Calc you can set the lead screw pitch. Make sure you are configured for ...
Hello :-)) The problem is solved, thanks to all the guys who give me some informations and typs . In fact it was a diode who was not wire in the good...
Hello group, I have ordered a Taig CNC mill and I will be using BobCAD v20.7 and TurboCNC. My questions are... 1. Does anyone else use BobCAD v20.7 on this...
... Hi Eric, I purchased BobCAD earlier this year but gave it up after just one week as the DXF import actually crashed the product. I have a lot of DXF files...
Hello group When i configure with fase\driver, i can have 4 normal steps (4 STEPS), or 4 normal steps with 4 half steps(8 STEPS) My question. Can I have more...
Dear Colleagues, I was using TurboCNC and sending the data to Phantom AutoCAD OLE/ADI Printer; however I cannot fing now this printer in my computer. How can I...
passion, Please explain what advantage there may be in trying to send indecipherable TCNC voltage output pulses/signals to an AutoCAD phantom printer. I...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
