Can the newest version of TurboCNC be compiled with Free Pascal, or does it have to be the Borland Pascal 7? What compilers currently work with TurboCNC?...
TurboPascal will NOT compile the latest version, but you can get either Borland pascal 7 or Delphi 1 at: http://www.vetusware.com/ Look under the system...
TURBOCNC5.EXE - TurboCNC 5 for Windows. [1444 KB] - Updated March 25, 2009. Since that date no news and no updates anymore??!! Although the comment was: "It...
... As a former member of that team, I can report that Dave K. disbanded it a few years ago - not too long after 4.02 was released - and decided to continue...
Hello, This email message is a notification to let you know that a file has been uploaded to the Files area of the turbocnc group. File : /USB for DOS...
turbocnc@yahoogroups....
Jun 7, 2009 8:13 pm
19747
Hello, One of the problems with DOS is getting a flash drive to work. I have played with several drivers with very little success. The usbaspi.sys with the...
What DOS are you running? D. ... From: rlwoodjr11 To: turbocnc@yahoogroups.com Sent: Sunday, June 07, 2009 1:15 PM Subject: [turbocnc] Re: New file uploaded to...
Hi everyone, I'm using TCNC v4.01 in a freedos machine, and generate code with Sheetcam set to tcnc post processor. When TCNC starts it shows this message:...
... Don't set the zero with anything but tool no. 0!!!! Any other tool will just set the tool length when zeroing during jog. I don't like this function. Might...
Denis, The tool handling of tcnc is not very intuitive to say the least. I don't use it. My tool holders which have a constant length for each tool and I zero...
... Thanks Denis, I finally understand why there are times I cannot get a tool zeroed and have been turning the machine off and back on to allow me to get the...
Hi guys, thanks for all the replies regarding the tool change procedure, I'll have to investigate the tool.tl file, perhaps there is a clue there. I don't know...
Hello... I use Old laptop for my Homemade cnc. It's in use few years now and works without peoblems. As is Old the turbocnc 4.x does'nt work good on that...
Slavko, The problem in 4.01 was due to the fact that no movement was made after the initial contact. Therefore the probe was in contact when the probing move...
... Hello Bubba.. I think there is no such problem but could be! I think you do best if you move probe to the center before next probe hit. In reality I don't...
Slavko, I have gone through the code a couple of times with pen and paper and cannot find any error in it! That is not to say I am just not seeing it, but I...
Hello.. I have BP7. I can compile Turbocnc v3.1 without problem But when I try to compile v3.1a I got error "code segment too large" (v4.01 can be compilled...
If you can compile 3.1 and 4.01, I cannot understand why 3.1a won't compile. Now also having said that, I looked in 3.24? version and the G50 code is the same....
Hello, I modified the code so that you can jog 2 steppers with the Left/Right arrows. It can be downloaded at the yahoo forum for turbocnc. Just rename the 4th...
... I try to delete some text from source (writeln statments).. After deleting aprox 20 lines I'm able to compile it. Seems to be some odd problem with size of...
Hello.. I was try to find hole center (G50) with turbocnc v3.1a and 3.25 and both have same result Probe moved as excepted in 6 dirrections but on end of...
Hello, This email message is a notification to let you know that a file has been uploaded to the Files area of the turbocnc group. File :...
turbocnc@yahoogroups....
Jun 15, 2009 11:55 am
19768
Hello.. I found BUG in G50 code inside Turbocnc v3.x relases. The Hole center is wrong in X coordinate. Just locate G50 procedure inside turbocnc.pas and find ...
I'm very dissapointed to notice that even after three months now we have not received any news nor any updates from AST about the new WIN Version of Turbocnc5....
Jan, No comments about TurboCnc5, I tend to run mills. As to 4.01 be careful what you wish for. 4 years and it has worked just fine for me, granted there some...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
