Hi, I am finishing up rewriting a G-Code generating program for a particular part to utilize a rotary table and the A-axis of TC v3.X instead of using circular...
The tool offset in T-CNC has never been about tool-radius compensation. It was (version 3.X), and is (version 4) about tool LENGTH offset. There is no cutter...
Hi, I was trying V4 with a simple program and I wanted to get rid of a few chips on the part before letting it continue. So I pressed the esc key to stop...
Neil: Cutter radius compensation has not been implemented in V4.00. The way that offsets work in V4.00 is to shift the display coordinates. Display Position =...
Hi, Neil: If by "tool offset" you mean the radius compensation (G40,41, 42), TurboCNC does not yet implement these G-Codes. They're scheduled for Rel-4.1. It...
... Here is what I did. I sat the start and acceleration to a low value and then cranked up the max speed to the point that I started missing steps. I would...
Hi I tryied to compile turbocnc version 4 using Turbo Pascal 7.0, and get the following error, when I execute the turbocnc.exe. I do this using Windows XP. ...
Paulo: Runntime error 200 is divide by zero. Did you run CrtFix (it's in the files section) to patch crt.tpu or the TurboCNC executable? If you patch crt.tpu...
Antonius, Thank you for your reply. I ran the CrtFix and the program is executing know. The executable has size of 450Kb, Is this a problem? I am a newbie to...
Paulo: I can't say for sure that it will. We stopped testing TurboCNC in real mode back in February. It is something you need to be aware of. We did find a...
Tony Ok. You say a thing that I am curious about, real mode, turbocnc can run in protect mode? Paulo Paulo: I can't say for sure that it will. We stopped...
I have a 5mm pitch ballscrew on my z-axis, and I do not write my G-Code in metric units. This results in a 0.000123031" per step resolution with my 8X ...
HotFix 08/31 Posted: 04/09/01 Details: The rotary axis problems of display position not being updated properly in jog mode, and improper motion in all modes...
I thought it should work with the 12" monitor as well. But for some reason anything below 800x600 will not fill the screen. I have tried to adjust the ...
Dan: Version 4.00 maintains 3 sets of coordinates: - psQuant, the actual digitized position in mahine coordinates - psReal, the ideal position in mahine...
... Thanks for the explanation, makes perfect sense now. ... Are you kidding me?? Took so long, my arse. You did it in 2 days. You are waaaayyyyy to hard on...
Having a problem with homing the axis of my machine when using V4. Any suggestion on what may cause the problem? Running on a 166 MHZ Pentium with no mouse and...
Hi, Paulo: You'll need Borland Pascal 7 or Borland's first edition of Delphi (modified to generate DOS executables) to successfully build TurboCNC. TurboCNC-4...
... V4. ... DOS. ... abort ... Hi, I am having the same issue - I haven't yet scoured the forum for earlier answers but noticed this one on the first page. I...
Hi, Paulo: Borland's Delphi will correctly compile the source code for TurboCNC. During the development cycle, Dave and Tony used Borland Pascal and I used...
Paulo: The original version of Delphi will compile a dos executable. The instructions are in the Programmer's Guide. I've posted a file containing the Delphi...
Hello, I have the same probleme with home speed: work fine in imperial mode but in metric mode the speed's VERY TOO slow ! I toggle imperial, make the homming,...
I am trying to run TCNC 4.0 on a Pentium machine with 16MB of RAM, and a 1GB hard drive. The computer has Win98 installed, but I am "F8 ing" at startup, and...
Hello, I have the same message on a Pentium 75 Compaq LTE5000 ! I can't understand the gravity of this message Can someone explain ? Francis ... From: "Jim D....
Francis, Jim: I just from a bootdisk created with the Windows '98 download from bootdisk.com. My 486DX2-66 does not report this error. There are two possible...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
