I think you have missed my point (& Rainbrain). If I start Twinkle and it does not identify my NAT type correctly, then it shows a message: "Cannot reach Stun...
... No, i think you missed the point of Michel. His advice was aimed to get your twinkle running without any errormsg or even STUN problems. The suggested ...
... for sipgate: 5004-5009. see sipgate setup instructions at their site, as well as twinkle-system-network settings, related whatsThis-help and for the one ...
OK life's too short for this. Incidentally all the ports required are forwarded and STUN works fine when Twinkle recognises the NAT type. I am sure that if I...
Hello, sometimes during a call to a landline I can't understand the other party because twinkle plays very choppy sound. I observed that this is the case if ...
Jens-Erik Hansen
Jens-E.Hansen@...
Feb 1, 2008 7:13 pm
2330
... When _the_right_ ports are forwarded _correctly_, STUN is of ABSOLUTELY NO USE. The other way round: as long as you need STUN, ports *are* *not* forwarded...
If this problem happens with every voip device you try, then it seems to me that the problem is in the media gateway of your provider. /Michel ... -- Michel de...
Hi, Can new codecs be easily integrated into twinkle ? I mean , the source code may require changes .. so would it possible to easily support other codecs such...
Hi :) ... Thanks for the advice :) Strangely, STUN sometimes works and sometimes it doesn't. (And I'm not really supposed to open ports on "my" NAT) But...
Doris, BTW: which model of NAT/router do you have? Often the root problem isn't NAT, but some kind of SIP functionality built to the router, that conflicts...
A little more code changes are required. Most of them in the audio directory. New subclasses for the audio encoder and decoder must be implemented. Furthermore...
OK I think I have understood you correctly. I take the time to point out that there is a point in your programme where an error state occurs, an information...
... This is no error state in twinkle, it's a failure in network connectivity. ... it's a warning about a failure in network connectivity. Compare similar ...
Hello Michel, ... I made further tests and I noticed that this only happens with softphones, I tried twinkle and ekiga on a notebook and on a desktop system...
Jens-Erik Hansen
Jens-E.Hansen@...
Feb 2, 2008 5:34 pm
2340
... sounds like a problem with gateway echo suppression. Do you use a headset when talking "by PC", or is the builtin mic catching speaker 0voice from far end?...
... I don't think, ">your< programme" is the right word here. Either it's >our< program, or it's >Michel's Program<. Please don't blame Michel for any opinion...
Let's put an end to this discussion. I think both Andrew and Joerg have made valuable suggestions here. Andrew has pointed out the problems he has with STUN...
You are right, it is a warning state, not an error state, and the inappropriate action applies to my set up, so continuing to start might be the correct thing...
Hello Joerg, ... for my tests I used a headset and I muted line out. A question for me to understand the problematic nature better: is it a typical symptom for...
Jens-Erik Hansen
Jens-E.Hansen@...
Feb 4, 2008 2:29 pm
2346
... typical ... my ... yes, the echo suppression is usually to be found in every gateway. It mutes the lower of both directions, thus continuously modifying...
... It's not mandaroty at all to include "Contact" header in a **negative** (3XX,4XX,5XX,6XX) reply. Note also that a negative reply **doesn't** create a...
Hello Joerg, leveling down the mic solved my problem. Thank you for the explanation. Greetings Jens...
Jens-Erik Hansen
Jens-E.Hansen@...
Feb 5, 2008 10:13 pm
2350
Hi, if a UAC sends a MESSAGE to other through a proxy and this one stores it because destination user is offline, then the proxy replies with "202 Accepted"...
... Maybe I could finish the phrase... XD If you need to try, you can send a MESSAGE to: sip:test@... You will receive a: 202 User offline, your message...
I noticed this behavior last week too and have handling of the 202 on my todo list. I have never seen the Success header. It seems like a proprietary header to...
... Please extend this point of your todo list to include some sort of feedback for a mere 200, like i suggested some time ago (you remember, changing ...
... Yes, I think I didn't understand well. There is not a "Success" header, what I read was: ... "7.3.1. "202 Accepted" Response Code The 202 response is added...
I get complaints that the quality of the sound at the other end, i.e. my voice transmitted, is poor. I know little or nothing about VOIP, and I wondered if the...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
