AOA, i am mcs student from ilm lahore ... and want to join your group.. take care... __________________________________ Do you Yahoo!? SBC Yahoo! DSL - Now...
Apologies, this is somewhat off topic for this group. I will be using ultimaserial while doing this logging though :) I need to log the voltage drop across...
I don't quite understand. I will not be removing R1, only perhaps decreasing its value some. The only reason I have R1 in this schematic is so that I can...
Is V2 also connected to ground? This is what I see from your circuit Vdrop = Thermistor/(R1+Thermistor)*5V You will have the maximum Vdrop when R1=0, but it is...
Hi all, I have an Excel VBA application, written a couple of years ago, that currently uses Dataqserial. I am considering converting this to a LabVIEW...
I have downloaded UltimaSerial and have run some of the vi's in labView 6.1 I'm using a DI-151RS as the input device with a 1.5 v battery for test source. ...
If you use GetData, the return is an integer array. If your analog plot takes a single reading at a time, you need to extract the data points from the array...
Thanks for the help. Turns out the loose nut behind the wheel (me) didn't get that I was getting DAC counts when switched to analog mode. Once I understood...
I'm just getting started with the DI-194RS kit and I am trying to use LabView to capture data. I found after installing UltimaSerial 1 and upgrading it to 2...
... I don't think you can just use the sample created for version 1. You will have to start from scratch. ... I 'd create a counter in the software and drop...
Ultimaserial doesn't handle file storage, in the sample codes, this job is done via DataqFile control. If you want to use DataqFile control to write VB...
Hi... Currently, i am doing a proj to capture image using a USB logitech webcamera n the platform is labview 7 express. Does anybody have expriences in doing...
I have a program that I passed on to a friend and it won't run claiming the trial period of UltimaSerial has expired. I have a registered version and the...
Each PC has its own serial number and the basic key is for that specific number only, thus you can't transfer file unless you have the super key from a site...
Hello, I am new to the group and quite novice to a lot of this stuff. I am trying to measure horsepower from a dynomometer with my DI-194RS. I need to be able...
-I use the dynomometer to measure power output from a Hot Air motor I built. " Stirling " It only usess 1 ONE analog input. It works great. I havent used it...
I hope someone can help me with a problem I am haveing trying to look at 0- 100 Hz. I am useing a long wire as a areo, I can see 60 cycles OK, but am getting a...
I would like to find the timer/real time/internal clock of the aquisition hardware and would like to display it on a VB program i am working on. how do i find...
I don't think there is an easier way other than getting the system time in VB or use the start time and keep track of the samples coming in to calculate the...
Ok, so yes, i've read all the postings regarding running labview 6.1 and the vi I downloaded from the ultimate site. Sounds like I need a new vi file, right?...
Joe - What signals are you looking for, natural or man-made? I'm not sure what sources of noise you might be getting that would cause problems at 7-8 Hz. Are...
madhay3: I've been writing a small program in VisualBasic 6.0 that eavesdrops on WinDaq to acquire two channels of data, and plot them on a 2-D vector plot....
madhay3: I've been writing a small program in VisualBasic 6.0 that eavesdrops on WinDaq to acquire two channels of data, and plot them on a 2-D vector plot....
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
