At the last meeting, I told Arthur I would send him an ASCII Chart. I found the document and decided I'd send it to the list since others might be interested....
Just received reminder about upcoming meeting. Last month Liam went with his Dad Scott, but there was no one there. They got there after 12. Is this...
Carrie Ross
imcross@...
Jan 6, 2003 11:46 pm
124
If I recall correctly, we had to meet in the room next to the one we have reserved (2745). Our first meeting at BCIT was on the 3rd floor. Did they go to the...
Hi Dave, Yes, they went to the same room as the first BCIT meeting. In any case, they may have arrived just after 12:30 so no one would have been around ...
Carrie Ross
imcross@...
Jan 7, 2003 12:50 am
126
Dear all, I am currently doing a study on the market of wireless internet that is emerging in the Greater Vancouver and across Canada. This study is required...
The International Robot Sumo Tournament is comming to Seattle on Tuesday March 18th, 2003 The IRST is a robot sumo event that is sponsored by Fuji Soft. They...
Here's some pictures of my brothers Mini Sumo, in it's completed form. -- Dave Hylands Vancouver, BC, Canada http://www.DaveHylands.com/ ... From: Jon Hylands...
Today, at the meeting, a few of us were talking about 2 wheeled balancing bots. David P Anderson has built a really cool 2 wheeled balancing robot called nBot....
We also talked about line following robots. The Chicago Area Robotics Group had a line following competition about a year ago, and there was a very impressive...
Whoops, pressed a key that cause my last email to be sent prematurely. We also talked about line following robots. The Chicago Area Robotics Group had a line...
Yes, similar to that is Legway, a Lego bot that also does the two wheeled balancing bit, but with IR proximity sensors to see how close the ground is at each...
i am new in robots. i found it is complicated. i need some one tell me the basic steps to design that robot using microcontroller. Especially its sensors . ...
Hi Egy, Could you please be more specific in your question? What would you like to know about sensors? What would you like to know about microcontrollers? ...
hi i am doing a project which its aim is to detect mines using robot. that robot ofcourse must have motors,sensors such as ir sensors,switches which protect...
Does anyone know of a general electronics club in the Vancouver area? I'm working more with process controls using AVR microcontrollers than anything robotic -...
If you're interested in BEAM stuff and obtaining inexpensive parts, this looks like a neat site: http://home.ust.hk/~bcandyp/solar.html -- Dave Hylands ...
Hello there... I was just wondering where in Vancouver I can buy (hopefully cheap) an RS232 Test board. Basically I'm looking for a board that can hook up to a...
Hi Mony, I'm not sure where you would find something local. The usual electronics places are Active Electronics which on first and boundary. RP Electronics ...
... I don't know of a club but the IEEE may have something that you're interested in. http://ewh.ieee.org/reg/7/vancouver/ Take care. Guy -- "Embedded and Open...
Hi i need someone have done a robot before TO tell me the first steps to do the robot. Such as could i begien from its mechanical design to know which motor i...
Hi engy, Everybody has a different approach. It depends on what your design constraints are. For example, for mini-sumo, there is a size and weight constraint....
Intek is good for common ICs and run of the mill parts. They're on Boundry about a half block south of Active. There's also a place called eParts, not a lot...
Oops, eParts is also on Boundry, just south of Lougheed - in the little mall. Don't know the address. When you enter the parking lot, they're on the road to...
Hi engy, I also suggest coming to our next meeting if you can. You will meet a few people with similar interests (building robots) as well as see a few...
Howdy all. I've been busy hence my absence for a while. I have some soruces for neat stuff: Mr. Hobby in North Vancouver, #3-820 Marine Drive has lots of...
Hi Ryan, This stuff looks pretty neat. The radiotronix one looks really interesting. I can see a wireless serial link down the road :) Thanks for sharing. -- ...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
