sorry for the verry late reply, my monitor has been down, and online mail uses a reply address that dosn't work with the listserver :( anyhow depending what...
dan williams
dan_williams@...
Feb 3, 2005 6:29 am
1341
... corry did I already tell you about the mecha link that was going around in #robotics? dan ... -- Dan Williams, Owner http://eds.dyndns.org Electronic...
dan williams
dan_williams@...
Feb 3, 2005 6:29 am
1342
hah! and there it is! dan ... -- Dan Williams, Owner http://eds.dyndns.org Electronic Device Services (604) 886 0316 RR8 855 Oshea rd Gibsons BC Canada V0N 1V8...
dan williams
dan_williams@...
Feb 3, 2005 6:31 am
1343
I noticed some talk about PIC programmers. I have a PICStart Plus available for cheap if anyone is interested......
Hey Ryan, I was the one asking... and haven't had any luck so far. How much you asking? And what comes with it? Thanks, TJ I noticed some talk about PIC...
There's a book available here: http://www.smileymicros.com/ And the first two chapters can be downloaded for free. -- Dave Hylands Vancouver, BC, Canada ...
Reminder from the Calendar of vancouverrobotics http://groups.yahoo.com/group/vancouverrobotics/cal Vancouver Robotics Club Meeting Sunday February 13, 2005 ...
Hello Everyone, I just received an e-mail and phone call from Mathew Claxton from the Courier who is looking for information and pictures of interested members...
Hi All, Just a reminder that the meeting on Sunday is the registration deadline for the Walker Workshop. So far it looks like six people are confirmed, I...
I have one that was part of a contest packeage from circuiy cellar, However i couldent figure it out really and havent tried to do anything with it corey ... ...
Reminder from the Calendar of vancouverrobotics http://groups.yahoo.com/group/vancouverrobotics/cal Vancouver Robotics Club Meeting Sunday February 13, 2005 ...
Yahoo! Reminder
reminders@...
Feb 11, 2005 5:57 pm
1356
Hi, Here's somebody else's description of adding quadrature encoding inside a servo. http://homepage.mac.com/sigfpe/Robotics/encoder.html -- Dave Hylands ...
Hi Chris, ... On the wood-working front, I made a few jigs: http://www.davehylands.com/Wood-Working/Knock-Down-Cutting-Grid/ And a dado jig for my router (no...
And to think I was feeling so original too. Those encoders are really small. I wonder if I could cram them together 45 degrees out of phase and get 4 ticks per...
I think most servos are about 55:1 from that gear so it would be 220 ticks per revolution as it was pictured - not too shabby. The encoders don't have to be...
I want to get a little bit higher (360/rev), since the measured slop is right around there. For some reason there are 90:1 on the final output relative to the...
If your sensors are 90 degrees out of phase, then with a 1/2 white, 1/2 black disk, there are actually 4 equally spaced transitions per rotation of the gear...
... Well Brennan, It looks like we're the first. But let me remind you that the only development kit available until last month was the $500 kit. Our timing...
Hey Dan - I've made a DIY programmer and it actually works. I've used the CDLITE and EPICWIN, along with the PIC Basic Software. Just remember that you get...
Hey Folks, Yahoo! I've managed to build the DIY version of Mykes programmer(the one that uses the 74LS05) and it works fine. But I still can't get the book PCB...
*Dear Vancouver Robotics Club,* We would like to extend an invitation to all of your members who are ages 7 thru 16 to participate in the 2005 K*bot World...
Hi All, Due to circumstances beyond our control, the Walker Workshop set for February 26th 27th is not possible. They are out of stock on the walker, and the...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
