Thursday, November 30, 2006 Taming the Terahertz Devices that can control terahertz waves could pave the way for faster wireless communication. By Duncan...
Thursday, November 30, 2006 GPS That Never Fails A breakthrough in vision processing provides a highly accurate way to fill gaps in Global Positioning System...
Do you guys know of people or companies that have robots similar to this one? http://rotundus.se/index.php I'm working on a project for work and we need to...
Computer Swap Meet on Sat Dec 16th at the Capitol Hill Centre, 361 South Howard St, North Burnaby,approx 5500 East Hasting Street starts at 11 am ends around 4...
Reminder from the Calendar of vancouverrobotics http://groups.yahoo.com/group/vancouverrobotics/cal Vancouver Robotics Club Meeting Sunday December 10, 2006 ...
Yahoo! Reminder
reminders@...
Dec 4, 2006 6:09 pm
2171
I have a project on the shelf that is a "ballbot" using two gyro rings" not even much of a ple of parts at this point though... dan ... -- Dan Williams, Owner ...
dan williams
dan_williams@...
Dec 8, 2006 2:50 am
2172
Reminder from the Calendar of vancouverrobotics http://groups.yahoo.com/group/vancouverrobotics/cal Vancouver Robotics Club Meeting Sunday December 10, 2006 ...
Yahoo! Reminder
reminders@...
Dec 8, 2006 6:00 pm
2173
Hampster fredom ball + guts from tablet pc + webcam? To: vancouverrobotics@...: dan_williams@...: Thu, 7 Dec 2006 18:20:05...
Hi everyone, This is the event I mentioned at today's meeting: Roboexotica http://roboexotica.org/en/main.htm Visit the "Details" section to learn about the...
Hello all, I was hoping the Vancouver Robotics Club might be able to help me out... I am a Mechatronics Engineering student at the University of Waterloo, and...
nrcavan@...
Dec 11, 2006 9:04 pm
2177
Hi everyone, A few people asked about the little green 96 x 16 pixel display on my ARM board at the last meeting. It turns out that it's available from Digikey...
The following message was posted over on the DPRG list, and I was planning on writing something similar, but Eric Sumner from the DPRG beat me to it, and said...
Some months ago I brought my old Toughbook CF-25 in and showed the group the protective jelly-like material used to encase the harddrive and protect it from...
Hi Phillip, Thanks for the link. Here's a datasheet for it: http://www.liquidplasticsolutions.com/pdf/flabbercast.pdf I hadn't heard of it before, but it does...
Thanks for the link, Dave Finally, someone else confimed the same information I have gathered about Duracell and Energizer batteries. My tests have shown that...
Hi Dave and the rest of the club: In regards to that survey, for me I have just 2 weeks ago switched to a steady 10-6 job. Prior to that I had different shifts...
Your Recommendations Are Requested We are seeking material that can be applied to 18 gauge aluminum sheetmetal. It will allow our serpentronics (robotic...
Trevor Gibbens
tgibbens@...
Dec 13, 2006 2:02 am
2185
You're invited to Phillip Beynon's Christmas Party WHEN: This Friday, December 15th 2006 between 4 and 8 PM WHERE: Suite 2103 - 808 Nelson St. Vancovuer BC...
Hello everyone Robotics at Chilliwack Secondary is in its infancy stages. I've started with tethered robotics, line following through "sandwich robots" -...
If it doesn't have to be Plyurethane you can check a Home Depot or Canadian Tire for liquid rubber. It sticks to almost everything and comes as a spray or a...
i know they also sell a liquid rubber that you can dip the handles of screwdrivers and pliers into to create a rubberized grip. this might work for you corey ...
Hi Trevor, My first selection would be a polyurethane mix, its not really that difficult but it can be a bit messy. Next choice: look for some of those...
Hi Neil, You might have luck working through some of the local technical and university programs. I know that BCIT (http://www.bcit.ca) has an industrial...
This looks like a lot of fun: http://www.youtube.com/watch?v=oVkp3KQFJac&mode=related&search= In this one the markings for the course are quite visible: ...
Hi Lee, ... You might need to adjust the speed associated with the AVRISP. I think that you need to run at about 1/4 of the speed of the processor and the...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
