it wouldn't happen to be the channel 36 crystal out of a CB would it? if so, it mgiht be 27.365 MHz I'm no ham dan ... -- Dan Williams, Owner ...
dan williams
dan_williams@...
Feb 3, 2008 5:49 am
2601
Hi Dan, The crystal is driving an stk500v2 programmer (atmega8) so I'd guess it should be 3.6864 or 18.432 Mhz or something compatibe with 115200 baud. The ...
hmm, well, pull it, put in on an avr with a led flashing program and compare against some known crystals :) dan ... -- Dan Williams, Owner ...
dan williams
dan_williams@...
Feb 4, 2008 6:03 am
2603
Hi James, ... Also, check the CKOPT fuse. It should be programmed (i.e. set to zero) in order to activate the rail-to-rail mode which some crystals like. -- ...
Reminder from: vancouverrobotics Yahoo! Group http://groups.yahoo.com/group/vancouverrobotics/cal Vancouver Robotics Club Meeting Sunday February 10, 2008 ...
vancouverrobotics@yah...
Feb 4, 2008 5:58 pm
2605
Big Computer Swap Meet Sat February 9 Hours:11am-4pm Croatian Cultural Centre 3250 Commercial Dr, Vancouver,BC Admission : $3.00 Kids under 12 FREE Tables $40 ...
should I mention for a negiagable cost you can just do toner transfer using hihg quality inkjet paper? dan ... -- Dan Williams, Owner http://eds.dyndns.org:81/...
dan williams
dan_williams@...
Feb 5, 2008 8:09 pm
2607
and... sorry missed your point for a sec, how about a pen knife? if you coudl find the right shapes in a crush-cut type punch, it might work, but it might...
dan williams
dan_williams@...
Feb 5, 2008 8:09 pm
2608
I am hoping someone can help with a picBasic code for a PWM sent out of RA0 and RA1 of a pic16f627A chip. I am trying to see if I can make this 8x8 matrix LED...
Reminder from: vancouverrobotics Yahoo! Group http://groups.yahoo.com/group/vancouverrobotics/cal Vancouver Robotics Club Meeting Sunday February 10, 2008 ...
vancouverrobotics@yah...
Feb 8, 2008 5:55 pm
2610
Please suggest a source for these metric machine screws. Phillips pan head are preferred. Mabuchi motors require these fastenings. 1. 2.6 mm diameter 2.5 mm...
Trevor Gibbens
tgibbens@...
Feb 9, 2008 4:28 am
2611
Here is a great opportunity to be an educator, play with fun robots, and get paid for it! If you are interested contact Debbie MacDougall directly - her...
RP Electronics (on Rosser a block south of Lougheed Hwy) carries a variety of sizes of metric screws in small packages. There's a good chance of finding 2.6...
Hi Trevor, ... I'd check with Pacific Fasteners. They're only open M-F during normal business hours, but they have the largest selection of fasteners I've ever...
We were talking about Eagle at the meeting today. This is the Eagle Tutorial that I really like: <http://myhome.spu.edu/bolding/EE4211/EagleTutorial4.htm> -- ...
Hi There, I'm new around here and I notice that the main website shows the next meeting as being on March 11th. March 11th appears to be a Tuesday and I...
Hi Daryl, ... Doh - I guess I should look at a 2008 calendar. Yes - Sunday March 9th is correct. I'll fix the website tonight. Thanks for pointing out my gaff....
No worries. Thanks for the quick reply. - D ________________________________ From: vancouverrobotics@yahoogroups.com ...
Daryl Hutchings
daryl.hutchings@...
Feb 19, 2008 1:31 am
2618
Hi there, I am a member of this club, Since I was busy unfortunately I couldn't participate any of meetings, but I am really interested in this area and I...
Hey all, I recently decided to start using Atmel AVRs, mainly due to the lack of a free C compiler for PICmicros (I'm a Linux guy). I've managed to pick up a...
Hi Jeff, I started AVR programming with the sumovore as well and used the same programming cable after on breadboards (still use it after more than 3 years). ...
HI Jeff, ... Not sure of anyplace that sells AVRs locally. I often buy mine from DigiKey. We've done group buys in the past. SparkFun also has quite few...
Hi Markus, I'll try again - I really shouldn't be working on stuff that late :P It's pretty easy to fry something when you're not really paying attention, ...
HI Jeff, ... I'm not sure why you would need to hold down the reset button. I certainly don't ecall ever doing that on my sumovore. ... The robostix is only...
Hi Dave, I don't know what's up with the reset button thing. It certainly wasn't in the documentation, but I spent about two hours on the day I got it, trying...
HI Jeff, ... So the reset line is used during programming. Normally its connected to the programmer and the programmer asserts the reset line as desired. The...
The fact that you needed to press it manually suggests that there is a bad connection on the reset line from the programmer to the sumovore. Could also be that...
Hi Jeff, I'm using a homebuilt stk500v2 programmer with avrdude under gentoo. http://tuxgraphics.org/electronics/200705/article07052.shtml I'm having some...
I use avrs with linux as well (also debian) I just set up a new machine latley (upgrades, prev devel machine was installed about 3 years ago) I have...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
