... it. ... 1. In HandRoute Select TopPrint as foreground layer (cyan) by pressing F2 several times (or use Set Visible Layers from the View menu). 2. Right...
57
Bob
bobbldr
Dec 17, 2008 7:38 pm
Looking for a 8530 USART can any one help?...
58
will.wasson
Jan 6, 2009 10:49 pm
Hi, I'm having a problem converting heterogenious parts into Orcad. All I'm getting are the wires going to the part but no parts. Anybody see this before? ...
59
nnavanaza
Feb 4, 2009 1:13 am
Hello, I have a 4 layer board design in which the two inner layers are ground and power. I need to reduce the zize of the copper on both ground and power...
60
ep104000
Mar 11, 2009 10:22 pm
I´ve rying to import Protel DXP footprints libraries into the WinQcad library, however, I see the extensions are different. WinQcad asks me for files with...
61
cpatnoi
Mar 12, 2009 10:04 am
I'm using a connector, CON_HDR::2X8A. Is there any way to flip the part in PcbEdit? I can flip it in SchEdit by pressing the "X" key but I can't flip it in...
62
Will Wasson
will.wasson
Mar 12, 2009 3:38 pm
Do you mean you want to place it on the bottom of the board? If it's a through hole component then that would do the trick. ... From: cpatnoi...
63
cpatnoi
Mar 13, 2009 3:04 am
The connector will be placed on the bottom of the board, but I need to flip the pin numbers along with the trace in the board layout. Pin 1 must be in pin 2's...
66
phamdv2001
Apr 8, 2009 8:23 pm
I would like to place the SMT component at the bottom of my PCB Please, show me direction/ steps how to do this. Thanks Duke...
67
Will Wasson
will.wasson
Apr 9, 2009 6:19 am
Hi Duke, This is pretty simple. In PcbEdit select the part you want on the oposite side of the board. Do a CUT on the part. Hit the F2 key to flip the board...
68
neocps1
May 12, 2009 11:32 am
Hello, I can't find these parts in winqcad. Is there a way to get them since I need them for a project ? thank you ! david...
69
Will Wasson
will.wasson
May 12, 2009 3:48 pm
Hi David, The easiest way to get these parts is to just make them! It is really kind of simple. You should only have to do the schematic symbol, because the...
70
neocps1
May 13, 2009 7:27 am
Thank you ! This is also the solution I have found. I have finished designing the eZ80 part, placing the pins the best way to simplify my schematics. Next I...
71
Will Wasson
will.wasson
May 13, 2009 3:18 pm
The easiest way to ensure that the footprint matches your part is to just create a schematic with all your parts on it. It doesn't have to have any ...
75
hossam Anwar
eng_hossam123
Jun 19, 2009 12:47 pm
please help,  i need the schmatic circuit diagram for 8051 kit programmer as in picture attached  best regards please help, i need the schmatic circuit...
78
wijono
Jul 24, 2009 9:14 am
Hi All I'm new member here. I tried to make a pcb of a simple circuit. After drawing the schematic, running pcb layout, I perform an auto-routing. The...
79
Mithat Konar
mithat_konar
Jul 24, 2009 11:37 am
The autorouter will run forever if you let it; it continually tries to find an even better routing solution than the best one it has found so far. If a long...
80
wijono
Jul 24, 2009 2:07 pm
Hi Konar, Thank you for help. I followed those steps, and found the routing is ready in Handroute step after autorouting stopped. Then, I ca also extracte the...
81
wijono
Jul 25, 2009 7:26 am
Uupps .. I found the route, isolation route. Great! Thank's, again Rgds Wijono...
108
saima
soniaakram60
Dec 16, 2009 8:24 pm
Untitled Document Bikini Bash...
109
saima
soniaakram60
Dec 18, 2009 1:24 pm
Untitled Document Bikini Bash...
110
hossam
eng_hossam123
Dec 22, 2009 11:09 pm
New Updates in my blog Electronics center Blog http://electronics1000.blogspot.com/ <http://electronics1000.blogspot.com/>...
111
David Jones
davidj.vpac
Dec 22, 2009 11:28 pm
unsubscribe From: winqcad_group@yahoogroups.com [mailto:winqcad_group@yahoogroups.com] On Behalf Of hossam Sent: Wednesday, 23 December 2009 10:10 AM To:...
112
M
mdfloijd
Dec 30, 2009 7:43 pm
I purchased in 1999 winqcad. Is there a version which I can unlock with my old code....
113
n_rohl
Jan 6, 2010 9:58 am
I have completed a PCB design with some changes and lots of annotations in the handrouting module after autorouting. I would need to effect a small change in...
114
John Knight
johndknight
Jan 6, 2010 3:15 pm
N_rohl, In general, you can do this by using the Call PcbEdit item in the file menu of HandRoute and click on "while preserving the current routing. This will...
115
ashishmeshram46
Jan 22, 2010 5:03 pm
Hi, It is my pleasure to inform you that on December 1st, 2009 your information was reviewed and accepted for inclusion in the 2009/2010 edition of our...
116
duc pham
phamdv2001
Jan 28, 2010 8:21 pm
John, How about if I am working on handroute and want to go back and change at schematic level. Is there a way do modify schematic without redo all the lboard...
117
John Knight
johndknight
Feb 1, 2010 10:03 pm
Duc, I do not use the schematic module so I am not absolutely sure. (I use OrCad) I think you can edit the schematic and create a new netlist. Then I think ...
