Still have a 1982 IH with GO fiberglass van to sell. It is job ready and going cheap. Open to any offer with or without genset,sheaves,lube etc. Also have some...
Dear Sir, Please send me your personal address as I cannot seem to contact you otherwise. Sorry for the chatter on wireline. Sincerely, Dewitt Jones ... From:...
I have a 1" temperature tool that I need a schematic for. I don't know the manufacturer of it. The tool is open, has what appears to be a line driver ...
It is a Pengo tool. I have schematics of a few Pengo temp tools, but not the one with that particular pcb. Maybe I have one close if you can describe the...
Since it is 1" tool, I don't see room for a transformer. It has three pcb's, the top board looks like 015-1700-254, has 3 cans, two orange-colored zeners. ...
OK, it is a pretty simple tool then. I will look to see what I have in the way of a Pengo schematic that might match it somewhat. Bell and others used that...
Hello I am a new member I want to buy a portable printer for print electrical logs in the field do you know where can i buy this printer and how much is the...
I can sell you a new one, if that is what you're looking for. Also, we can modify most gamma ray tools to stack with an SIE bond tool if you already have a...
... Horizon Cable Service, Inc., 1-800-621-8129 1-405-789-7125 I called, Jennifer says they can do it. I have no experience with Horizon. Steve McLaughlin...
... Thanks for the info, Steve. It turns out that the owner of Horizon and the person that splices multiconductor lines, including 3/16", has re-opened a shop...
I have an SIE caliper on the bench. It is the one with the funny little linear pot with four elements that can be slid into a new position when it wears....
I actually fixed that slide wire pot in the SIE Caliper. The element is made from the resistance element from an old large ten-turn pot. I used a 100K pot,...
Radiation Sensors, LLC is a manufacturer of gamma detectors with several years of experience in manufacturing ruggedized gamma detectors for logging tools. You...
Welcome to the list Ival. I have been talking to Ival for some time about scintillation crystals. By way of introduction to the list, he is a pioneer in the...
Hello, I would like to introduce myself to the group. My name is Adam Green and I work for ASEP USA. We manufacture Wireline trucks and Skids among many other...
I will be out of the office starting 09/24/2004 and will not return until 10/04/2004. Please contact Rob Kish (265-6060) or Munir Sharar (769-3026) should you...
I will be out of the office starting 09/24/2004 and will not return until 10/04/2004. Please contact Rob Kish (265-6060) or Munir Sharar (769-3026) should you...
I will be out of the office starting 09/24/2004 and will not return until 10/04/2004. Please contact Rob Kish (265-6060) or Munir Sharar (769-3026) should you...
I will be out of the office starting 09/24/2004 and will not return until 10/04/2004. Please contact Rob Kish (265-6060) or Munir Sharar (769-3026) should you...
I will be out of the office starting 09/24/2004 and will not return until 10/04/2004. Please contact Rob Kish (265-6060) or Munir Sharar (769-3026) should you...
Do any of you math whiz kids (Herman or Chuck maybe) know the optimum setting for the linearization pot in a caliper? What these things are doing is matching...
More thoughts... The linipot / slide wire divider configuration creates an exponential function overlaid on the sine or cosine function of the caliper arms....
After a couple of mis-fires, I think I am officially logged into this group... My name is Don Thomas - I work at the University of Hawaii on the Island of...
Welcome aboard Don! Carl ... -- The very existence of flame-throwers proves that some time, somewhere, someone said to themselves, "You know, I want to set...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
