Bruce: If all else fails (or there is no "all else") you might try Oilware, Inc. (www.oilware.com) The folks at Oilware have done some stuff with recovering...
Hi Dan, Thanks for the tip on Oilware. I'll contact them to see if they can help Bruce "Krygowski, Daniel (DKrygowski)" <dkrygowski@...> wrote: Bruce:...
Sondex Inc. is currently looking for an experienced Technician/Senior Technician to work on downhole tools. The position is based in Conroe, Texas and will...
hello sir,,, how are you i am Hesham from egypt ,,i hope that you are good and enjoy your health i am working as well site geologist here in egypt in petroleum...
Good morning hope everyone is having a good week. I am looking for the Schlumberghe cement bond log calculations for amplitude (specifically 80% bond) for...
To All, This year, Oct. 2nd - 4th, the wireline, HSE, and associates committee will be holding their annual Safety/Wireline conference in Ft. Worth, Texas at...
I just published this page on Shooting Panels: http://www.logwell.com/tech/shot/shooting_panels.html Anybody see any problems or have any suggestions for stuff...
Call Mike when you can..3252072084 or 3255738750..WORM ... From: Kenny Jordan <kjordan@...> To: wireline@yahoogroups.com Sent: Tuesday, August 8, 2006...
I worked for sie for a few years and will contact a person that was in their customer service with your reqst and see what he knows,if you still need this...
I would still like to know how the darn things are really supposed to be connected. Note there are two ways to connect them in series as well as connecting...
The reason for 2 coils was to eliminate some noise issues..magnets are much cheaper than coils. ... From: "AnaLog Services, Inc." <wireline@...> To:...
After talking with tech that used to work these,you should haven orange and yellow wire on each coil. ornage from one coil connect to yellow of other coil and...
Interesting. That puts the coils in series with the outer lead of one connected to the inner lead of the other. Thanks for the info! ... From: Gary Albin To:...
Not at SIE! I guarantee it was done to save money given Marion Hawthorne and Al Biggs being the ones calling the shots (heck, they used consumer grade carbon...
That's the reason for "magnet chargers" to recharge the magnets too. Obviously the magnetic flux density affects sensitivity! Hey, who'd of thunk it? A ccl...
i am a senior logging engineer from ALGERIA.run all openhole services and cased hole too. perforations,plugs and sondex tools. i am available and thanks best...
I work for oil instrument about 10 years,I was soft and electronic design.I have a friend.we can use DSP and ARM etc design circuit for cortrol.Maybe we can...
Dear sir I think that CAST-V,circunferential acoustic scanning tool a halliburton trade mark, is a good tool to be used in all cases even when microannulus is...
Hello, I want to run CBL through 2 casing strings, is that ok? Mason Gao Operations Engineer Abandonrite, a service by Nabors Production Services Phone: (403)...
Does anybody have a neutron sleeve calibrator that would like to sell? We are looking for the fiberglass looking one GO made. Syd H. Levine AnaLog Services,...
It depends somewhat on which cement bond tool you are planning to run, and on well conditions. I have proven well integrity here locally through multiple...
I think yes you can run CBL in multiple casings. you can allways get usefull information. The first arrival on the wave train will teach you about the cement...
Hi, Does anybody know where to get Schlumberger IDW measuring wheel from? It measures 30" circumference. Any info on the company that make them, or any...
But Cast-V gives information bond between Casing and cement . It can't give information about bond between cement and formation. From: "kacem_h_2000"...
\Hello Wijoyo, From your inquirie it sound like you are an ex schlumberger . What logging company are you working now. regards Budi ... Send instant messages...
The CAST-V tool is sensitive to borehole geometry,centrilization and scales by design,I think the conventional good working calibrated CBl tools ,better more...
Hi! I would like to let all Production Logging Experts know about our conference, Production Logging 2006, Aberdeen, 28-29 November. At Production Logging 2006...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
