Hi Ian, You mean the value displayed in the status column Ian ? This value is calculated and updated by the returned .event message from your endpoint - could...
Hi Kevin Yes the status column on the status page within homeseer. Using the pull down box on the same page to set a level to say 50% for an X10 device the...
I hadn't used HS for a while but have downloaded and installed it and I'm seeing the same Ian. The xAPBSC.cmd issued by HS is slightly off in its level it...
Paradoxically - If I set the device to say 50% from the mcs plugin (Level=50%) then my mcs device actually shows 52% in its status display and my 'James' based...
Hi Kevin, Thanks for checking this, I'll wait a while and see if anyone has the answer I've got plenty other bits to be doing. I have another question which...
I notice that if the level is first set from the dropdown - causing HS to display something like "Dim, 50%" then later incoming xAP events from say a switch...
Hi Kevin, I have just tested this and yes if you set HS to a level then the on/off commands from Xap change the status correctly but as soon as you use the HS...
Rick, TBH this has be a little stumped. I've tried a few things, well actually quite alot of things, and the only time i see similar behaviour is when the...
Hi, I've been a member of the group for some time now, but I finally have some time to start doing some development. I'm currently working on a web browser...
The schema for James original Homeseer plugin is here:- http://mi4.biz/modules.php?name=Content&pa=showpage&pid=10 There is an alternative , .net based, plugin...
Hi all, I've uploaded a new tool to the opnode repositories: http://sourceforge.net/project/showfiles.php?group_id=191203&package_id=248913 xAPalyzer is a xAP...
Just uploaded xFx v2.1 along with v2.1 Hubs and xFx Viewer v3.1 to the usual place http://www.edjo.pwp.blueyonder.co.uk/edward/xAP/ Not a huge number of...
Hi all, Although it's out of the scope of this list, I'd like to start a new discussion regarding the interest/need of having a low-level communication...
I haven't really looked in any great detail but SNAP is an interesting highly compact 'masterless' protocol - just not sure how it might handle collisions ......
Thanks Kevin for the link. Interesting project that SNAP. Unfortunately, the collision detection system (if any) is not explained in the document. Daniel. ... ...
Hi, I'm in the process of developing some xAP applications, which eventually once I get them further along I plan on releasing as open source, and I was...
Hi Mick, Welcome. Vendor ID's should really be a minimum of 5 letters if possible - could you choose a slightly longer one ? (Davis, DavisRes ?) - although...
Thanks Kevin, I wondered about that. Hmm, how about "domus"? I'm terrible at coming up with names for things and always seem to resort to Something Something...
Hi! I have a Tini and began to serioulsy think of using it for 1-wire to XAP connector (yes, I began thinking of that more than a year ago, but this time it's...
Also, can a single address have multiple subadresses of the same type? See page 4 of TSC Schema. I see that ID1 and ID2 are position outputs, but how are they...
... Welcome back Patrick ... The idea is that the 'device' portion describes the 'type' of the device , as such sensor is fine although you might prefer...
... adressing, ... Suppose ... and ... to ... they ... Oh, I wanted the tini to be transparent too: I was thinking of the left side "virutal devices" made of...
... How,and which endpoints you present via xAP is totally up to you, you can hide some and even create virtual ones should you wish. Just create a construct ...
... see ... Ok, thanks! I didn't looked at the implication of that scheme on the overhead (protocol). I can also see the limitation of having only 255...
... TBH Patrick it's an embarrasment that the spec hasn't been formally published. It's only a minor update, primarily to address that UID restriction, and...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
