I'm trying to set 'Include in Ping status' for a number of ping entries - I set it then update but when I edit it again, it's set to no :( Anyone know why this...
Maybe a little buggette? If you add a new ping entry and give it a group name containing an apostrophe i.e. Home PC's - it uses the internet naming for the...
james is working on it http://groups.yahoo.com/group/xap_automation/message/2959 ... entries - I set it then update but when I edit it again, it's set to no :(...
it appears switchboard will send xpl osd.basic messages w/ caller id info? this sorta mucks up my displays since i'm xpl based and already sending the cid...
Switchboard doesn't send xPL. Floorplan however, if enabled, will bridge Switchboard's display messages to xPL. What you need to do is target messages, just...
Hi, Is it possible for xAPFloorPlan to display the room temperatures? I have a TOM10 with a couple of sensors and I'm currently capturing the temperatures to...
Yes - you could forward the information via a suitable schema (even say an OSD message) from xPL to xAP and then display that info in Floorplan, (or you could...
If the data is already in an xPL message and you have xPL support turned on in Floorplan (bridging can be on or off, it doesn't matter) Then you can just add...
Thanks James, I had a look, the xPL message i am getting is: xpl-stat { hop=1 source=gshed-tom10.thefrosts target=* } sensor.basic { device=Bathroom type=temp ...
Hi Neil, This isn't going to answer your question on 'how to' - I'll leave that to James but it will explain why this is awkward and how different originating...
It then gets more awkward, especially for Floorplan, as xPL put context throughout messages in most schemas and this was one of the original reasons for me...
Tread water a sec Neil cos I think J has a solution for you - and it's already in the code ;-) As you've got the SQL logging working in xPL it makes sense to...
... Isn't that great :-) xAP Desktop (another great J application) allows similar as well Re the below I don't know if the 'type' parameter can change in your...
but, and there is always a but, the item value pairs are ANDs not ORs so if you have move than one then all have to be true Guess i'll be adding it to the...
I can now get the two (i've just got 2 sensors on the tom10 at the mo) temperatures displayed on the map, trouble is the temperatures are displayed side by...
Hi I was wondering if anybody knows why I get state unknown all the time in the hub from the X10 connector. I want to use the state in another application, but...
Hi Is there any c# source code availiable for a simple xap listner application? I just want to listen on the net for xap mess and sort out a spec message and...
Could you let me know the settings in Floorplan for each device and an example xPL messages that sets them? Could it be that both sensors are reported by the...
aiui, you will get an unknown state until a device is controlled ( by xAP or x10). The trouble is that the connector cannot query the current state of a x10...
I get two separate messages: xpl-stat { hop=1 source=gshed-tom10.thefrosts target=* } sensor.basic { device=Bathroom type=temp current=25.18 } and xpl-stat { ...
I am using xAPFloorplan and wanted to know how I can chain multiple BSC X10 addresses into a single command. I have a State Link that controls multiple lamps...
Tried out the Saver Server last night... Pretty cool. But it doesn't seem to see my weather install. News is detected fine. When I start the app (service...
Not particularly clear from the Saver server page but it needs both the weather.report and the weather.forecast from xAP Weather. Could you try configuring the...
Right i've figured out what is going on. It's nothing to do with xAP or xPL or anything on the receiving side. It's a fault with the code that delivers the...
... Currently the built in processing of links does just what you've found, sends a .cmd to each device. I'll see what i can do internally to group things...
That did it... thank you. BTW, what is the forecast field SUPPOSED to hold? I originally put in "1" to enable it, but then the forecast messages had a source...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
