... I agree ! It made me very angry and frustrated when i read in the messages that there was no answer from Doug, but then i decided to try it myself and...
hello all. it has come to my attention after browsing over some of the messages that some people think i read these on a daily basis. when i started this group...
Doug and Group I feel I owe you an apology. I was under the impression that this was the preferred route for support of your product. Thank you for ...
Rein, You are a thief. There is no dressing up that, whatever the reason. Mariss P.S. I have your name. I will never anything sell to you. ... If Doug did not...
Hi Doug I emailed you but it bounced, that was a month or two ago. I see you moved to TN. welcome to the East side of the USA! I feel there was a lot of Doug...
In a message dated 5/2/2002 5:25:02 AM Mountain Daylight Time, ... Agree completely, nor was it necessary to post to every other CAD/CAM list. The subject was...
I have created a table in the database section of the Yahoo website, to record motherboards tested/used with CNC Pro. I'd appreciate it if you would make...
... There is no Doug-bashing taking place, as far as I can see. CNC Pro is a slick program when it works. The problem is, that it doesn't work for everybody,...
Randy, You might want have someone make you a bootup disk using MSDos 6.22. Put CNCPro on the disk and run it from there. I have six different computers most...
I agree with the pure DOS computer for CNCPro. I have a Toshiba Portage 660CDT (Free from work). Running DOS 6.22. I have never experanced the jog key...
Hi Jeff, I am alot older than you! At age 50 I tend to be realistic. I know I have bought my last CNC program. I designed 10 different hobby milling machines....
hi i too belive that win or anything similar, today, with a well-tuned system, can run a big machine safely and stable. i currently use flashcut and have never...
Then Windows is not really running the mill. Your comment does not count because it was only used to mention someones elses software. I got complains about...
hm,...your right regarding flashcut; it uses win to tell the blackbox what to do, instead of doing the timing and sync itself, this is one way to get around ...
Hi, Is Swedish Dos MSDos 6.22 or simular? Or is it the Dos that comes with Windows. Have you tried FREEDOS from the internet? What gets me, is usually I get...
... Oh, I have 6.22. But Win98 booted to the command line (put "BootGUI=0" into msdos.sys) is actually MS-DOS 7. To go into the GUI (the "Windows" part) you...
Hi Randy, Try the MS6.22 bootup disk with CNCPro on it. Shut your hard drive off or disconect it. That P166 should work great. Have you tried FREEDOS from the...
Hi Al, Win95 upgrade had a Dos like Win3.1 The same thing with Win95A Then Windows 95b came out and some of my Dos programs went bad. Lots of game people...
Since I think I inadvertantly started this whole "support"thing a couple months back I feel I should A: Say,to Doug, "sorry I opened this can of worms"! and B:...
You didn't release any worms, Carl. There are unresolved bugreports about the jog key problem going back to last June. There are people who can't use their...
... Make that "performance/cost ratio is much higher..." :-) Best regards, Randy (posting from home email now) Randy Gordon-Gilmore ,----.___________...
Can anyone help me understand, how when using a demo of flash cut and it creats curves it use the letters I and K, but CNCPRO uses I and J? I have tried...
Hello, It seems that there are several CNC Pro users using a non-US keyboard, which may cause some weird problems. Having extensively used DOS for about ten...
Steve, I and J arc modifers (X-Y) for G02/G03 refer to the G17 work plane. I and K arc modifers (X-Z) for G02/G03 refer to the G18 work plane. J and K arc...
... Thanks wayne, all i want to do is turn some simple bullet shaped profiles, on the lathe, But what do i need to do, perhaps some one could explain or ...
I'm still trying to learn how to setup my machine correctly using CNCPro. After talking with may different CNC operators I got an agreement on how it should...
Jeff, I believe you must set the tool Parameters before you set the G54 Command. I think your 2nd and 3rd steps are reversed. ... From: jeffdavis516 To:...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
