John, The problem lies in the Corel draw still using the old polygon geometry. Instead making true circle, the circle is divided into smaller straight...
John, your 30" circle should have G code like this: % O0 (PROGRAM NAME - CIRCLE ) (DATE=DD-MM-YY - 01-05-03 TIME=HH:MM - 15:44 ) N100 G20 N112 G0 G90 X15. Y0....
Hi, Anyone out there who has interfaced CncPro to an EMCO F1 Mill using the existing steppers? My F1 has a rocky computer board and I think that this is the...
Hi Rob, As long as you get the stepper working, you can run your EMCO using CNC Pro. I have done it with my Dyna 2800. fortino ... From: robert brown To:...
Hi Fortino, Thanks for that, nothing like a bit of encouragement. I'll do that as an interim solution but I think I'll reequip with fresh steppers eventually...
I always use a spreadsheet or some other tool that lets me use division whenever math is involved. that way, each new position is within one step, and the...
Has anyone ever wired in the E-Stop option so that the software stops movement when a machine fault situation occurs? Any help will be greatly appreciated....
toons, I use the par port pin 10 pulled up to +5V at my controller/driver board. Set Cncpro to sense this pin. Anytime this pin is pulled low (to ground with...
Hi Mark, No bad thing to let the spreadsheet make the rounding decisions. In my case it's a difference of opinion between the CAM software and the Mill...
Anyone else have a problem with losing repsonse from number keys and or the + - keys under cncpro?? I have been using "Pro " since ver 1 Often when I go to...
Carl, I have had times when the keyboard will not activate the machine at all. I reboot and everything seems fine. I am running a Via C3 350 MHZ Proccessor...
I've had cases where it would appear that the shift key is stuck. Since I'm very new to all of this, I have not seen the problem ofen enough to tell if it is...
Does this still occur after Doug's recent (4/19/03) release? I thought that this was the problem that he was addressing and corrected. I haven't had a problem...
Al Never crossed my narrow mind to check for an update!!! will check it out. thanks Carl Does this still occur after Doug's recent (4/19/03) release? I thought...
Our machine seems as though it moves around an arc properly. I have created arcs using autocad. My drawing is in the shape of an 8. The machine runs nicely...
John, set the " I and J always relative" to "ON". Fortino ... From: acutecsystems To: yeagerautomation@yahoogroups.com Sent: Tuesday, May 13, 2003 5:54 AM ...
Has anyone reported problem with the new updated CNC Pro? Mine has running strange. The machine try to make stairway toolpath when following a spline. So far,...
As far as I know, the prog never has supported splines. RichD Has anyone reported problem with the new updated CNC Pro? Mine has running strange. The machine ...
Cncpro has been a stable, finished program for a few years now. Has anyone compiled a manual (other than the one being offered for sale awhile back)? Doug...
... has running strange. The machine try to make stairway toolpath when following a spline. ... Sounds like a problem with Abs vs. Rel coordinates. Make sure...
Joe, I have had it fix. Apparently, I accidently set the time from min to sec. This cause the machine runs too fast for its size. Thanks for the input anyway. ...
Hello everyone, I've been a member of the group for about two years now but I have yet to set up my system (talk about procrastination). My intended setup is...
List & Doug: Anyone know what options and target modes to compile ACE? I'm using BC5.02 and I can get an .exe to compile fine, but it hangs when I run it....
Yes Sir, That would be great . Getting to look at a working program would cut to the chase for me. Please post it or e-mail me .thanks Carl DFair35821@... ...
I have the program at work and will not be able to send it till after Monday at least. I will caution you about having "G18" as your first line of code. This...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
