Our 2-axis machine has been plagued with stepper motor lock-up problems on and off for the past year. We acquired some Baldor DC Servo Motors and Drives and ...
Gecko 320 should do the job for you. Excellent vendor, excellent support, excellent product. Depending on the resolution of the encoder on the motor, you may...
Gecko 320 should do the job for you. Excellent vendor, excellent support, excellent product. Depending on the resolution of the encoder on the motor, you may...
Hi Don; The solution depends on what Baldor servos you have. If they are brush type motors then the easiest solution is either Gecko or Rutex drives. Rutex...
Just a word of caution. Make sure the problem isn't your acceleration rate is too high. It is adjusted in the set up. I had a similar problem and thought it...
Mark - thanks for the response. Not sure about the existing encoder on the Baldor DC brush type servo motors. It is a Sumtak Optcodrer, and has 1000P/R on the...
Thanks Doug, Baldor motors are DC brush type. I am trying to go from the computer (CNCPro) to the Gecko, to the servo motor. I am using a 5VDC power supply...
Is there any way to get CNCpro to run an a newer computer with Windows XP ? I have tried it on 2 computers and have had no luck . -- Ron Kline American...
Ron, CNCpro requires MS DOS or DRdos. XP has NONE. You will have to create a dual system disc, put DOS on one, XP on t'other. Boot to which you want. RichD...
IDEA Can I put 2 hard drives in the computer and have 98 on one and XP on the other . Is there a way to boot from a different drive ? ... -- Ron Kline American...
Ron, Yes, but the OS situation is the same. 2 logical drives or 2 physical drives = 2 drives. An OS on each one. XP will still be the primary OS. A dual boot...
Anyone know what happened to the Yeager Automation website? Also, anyone know what happened to this forum. it seems to have been overrun with spam messages...
It's been that way for a while now. Doug surfaced about a year ago with plans to write some new cnc software. Just about everyone who replied to him said...
Too bad about it, it had a lot of potential. Does Mach3 have too width compensation? How much. Does anyone elso recommend anything else? What have most of...
By compensation do you mean cost ? Unfortunately I believe they are about the same , I think I payed $120 for Mach 3 and I don't know what CNCpro is selling...
YES. It has tool compensation. Have you ever tried Mach ? -- Ron Kline American Precision Ceramics .. (Industrial ceramics) Central Ky. ... -- Ron Kline ...
No. ... From: Ron Kline To: yeagerautomation@yahoogroups.com Sent: Monday, January 01, 2007 6:26 PM Subject: Re: [yeagerautomation] Re: What happened to Yeager...
No I haven't. ... have ... payed ... but ... sale or ... one ... and ... very ... almost ... too ... anything ... <mtebob1@> ... year ... everyone who ... long...
NO ! , what do you mean NO. Don't just sit there go download it and see what it can do ! It will take you at least a week just to read the instruction manual ,...
Yes , you will find it on the website home page , and they are VERY helpful even the dumb questions we all ask . -- Ron Kline American Precision Ceramics .....
... No problem That is why we have Ford Chevy Chrysler Dodge Toyota Honda and on and on -- Ron Kline American Precision Ceramics .. (Industrial ceramics) ...
Why don't you like Mach 3 and what did you choose? ... From: Ron Kline To: yeagerautomation@yahoogroups.com Sent: Thursday, January 11, 2007 9:29 AM Subject:...
I'm not familiar with Mach3 or any other similar programs. I'm sure there are some number of fine cnc control programs. That said, I am a big fan of CNCpro....
i agree with you Henery, i built my own cnc plasma table and was using the trial cncpro for setup and now i`d like the full version, i have tried other windows...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
