... just ... weren't ... The original build (described in that older BBS post) used the original version and config. It was almost byte-for-byte identical to...
Hi, I have a Linksys WRT64G router and whenever the device tries to daownload an update it always fails. I have the power management off on the ZipIt, but the...
I got the burn3 then openzipit flashes to work.. and put together a little ncurses application that does nothing more than getch() then echo what it got, as a...
Hello I'd be interested in turning the zipit in a VOIP phone. Ok, it'd be much simpler and cheaper to buy a dedicated one, but it would be *less* fun. ...
I see that gcc 3.3.3 is needed for the kernel and a 3.4 version for apps. Is there a way to manage two different gcc compiler versions from within one...
I don't actually have a zipit but was looking at getting one and maybe adding bluetooth aswell. From looking at all the documentation I believe there are two...
... original 16?) How much more RAM do you need ? How much more ROM/flash ? ... How about using the I2C bus for a I2C A->D converter ? (and hook in a regular...
... ??? Where did you read that ?? I've used GCC 3.2 for apps and kernel and mixed it with 3.3 as well. (ie. if you don't hit a true bug in a certain...
I moved the kernel to gcc 3.3.3 so that it would fit in the alloted space in the flash. Oringnally I built it with gcc 2.95.4, then 3.2, then 3.3.x and finally...
Hey everyone, I've managed to cross compile a few apps for OpenZipit, and I've thrown them on my site: http://www.santoni.ca/albert/zipit.html The apps I have...
Hello, ... Ideally 64 Mb, but 32 Mb would be fine ... At least 32 Mb. A 128 MMC would be just fine I'm quite sure everything won't fit in the 2 Mb - even if I...
Hello Bluetooth modules are easy to add to existing hardware. See externe.net/zaurus/simpad-bluetooth/ - I did that with a WML AHR C09 I got from Segor Germany...
One trick I have used in many of our products is to share bits. LEDs can be shared with CODEC lines by 'restoring' the LED state when done talking to the...
... Hmmm, maybe you're right. That's the way the OpenZipit binaries are compiled, but I guess I could stick with 3.3.3 for all. I want to produce the minimal...
Depends what you mean by password.. If you mean WEP key/passphrase, you can enter the WEP key manually using iwconfig. If you mean web-based authentication,...
Hey guys ive been reading up about the zipit on here for a few weeks and so yesterday i tried the burn3 firmware stuff and got it on no problem but from what i...
... That's a good idea. I'm thinking of mike detection and lid open/close besides the leds in such a way. They should not be too hard to solder. I've yet to...
I want to thank you for putting together this distribution - it does exactly what I wanted my zipit to do. One comment on the install readme: the script...
Ken, I generated a 3.4.2 toolchain and was able to produce a kernel. However, this kernel is non-functional on the device. Was this the same as your...
I was never able to get rid of the many errors that I encountered when I compiled my kernel sources with 3.4.2. What sort of messages come out the serial port?...
I have serial support compiled in, but I don't see anything besides the bootloader messages: Aeronix 7312 BootLoader with ZipitPet mods (1.16) Sizing Memory......
These are the steps I've taken to enable serial port output of kernel boot messages. I'm probably missing something here. - Under "default kernel command...
... To clarify: In Burn3 you can run the original app with zrun. However, when you switch to OpenZipit, you will *not* have the original app available. -Jim...
Everytime I try to run the zflash program i get a permission denied error. I know the file is not +x but I don't have a chmod on my zipit and I am using...
I've never used ProNFS, so this is based on general experience. On the windows box, try setting the permissions on the folder zflash is in to "full control"...
Looks like you have to mark the file Hidden on your Windows box, see: http://www.labtam-inc.com/index.php?act=faq&uid=7&pid=2 ... zipit ... permissions....
I rebooted after the ZipIt told me too and now every time i turn it on it shows a penguin on the Zipit Logo then the screen blanks and then it repeats. Any...
... What I know is that openZipit hasn't been updated, well pretty much since it was created. Atleast I havn't seen anything updated or if there is anyone...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
